background image

7

Surge Protection(RJ45 Port):

  This is a transient voltage surge-suppressor for network

or fax/modem protection.

Communication Port:

  WinPower software can be used with the UPS for power

management. Standard serial interface cable is compatible with 1K(S)/2K(S)/3K(S)
UPS, however, only the special cable supplied with the UPS can be used on 6K UPS.

Input/Output:

  If socket is available, just insert compatible cable plug. If terminal is

available, qualified electrician should be required for wiring and installation.

Note

: Terminal cover should be put back for safety reason after wiring completed.

Input Breaker:

  If the breaker is tripped, reduce the load connected to the UPS and reset

the breaker.

External Battery Socket:  

Dedicated battery power cable is supplied with the battery

pack. Insert the cable into the external battery socket on the UPS and battery pack output
socket separately to connect battery pack to the UPS. The same battery packs can be
daisy chained together to achieve desired run time.

Notes

: It is suggested that one battery pack can be connected with one UPS main unit.

Only the identical battery packs can be connected in parallel to the models with suffix 

S

to extend the backup time .Please consult the distributor for further information.

3. S

YSTEM

 D

ESCRIPTION

4.1  O

PERATION

 

ENVIRONMENT

Ambient Temperature: 0

°

C to 40

°

C

Height of sea level < 1000m
Relative humidity: <95%

4.2  B

ATTERY

 

APPLICATION

Simply connect the UPS  to the mains to fully charge the  batteries  for 12 hours prior to
use  is recommended. It can also be used  immediately  without charging the batteries
first  but  the backup time will be less  than standard level.
Under normal conditions, the  battery  life lasts 3 to 5 years. In case if  the battery is found
not in good condition, earlier replacement should be made. The replacement of the
battery should be carried  out by qualified service personnel . Please contact  the
distributor .
The battery  should be charged once every three months for at least 12 hours. In areas
with higher temperatures, the battery should be charged once every two months and
each charging period shall be at least 12 hours.

Summary of Contents for C1KR(S)














Reviews: