background image

Fig 3

ASSEMBLY OF THE TREE

1. Locate the bottom section of the tree which is identified

by a label on the outer branches marked “A” (Fig 5).

2. Remove the protective plastic cap by twisting and pulling

it from the end of the pole, (that is pinched to a point), and
place the end into the tree stand. Be sure the pointed end
of the pole extends to the bottom end of the stand.

3. Now tighten the eyebolts evenly on the tree stand; being

careful not to over-tighten (Fig 3).

ASSEMBLY INSTRUCTIONS

(We recommend wearing proper clothing in order to prevent 
scratches that may occur during the assembly process.)

Carefully unpack the contents from the tree’s carton (Fig 1); 
including the contents of the poly-bag that is adhered to the 
interior flap of the tree’s carton.
Contained in the poly-bag are LED replacement bulbs and a 
remote control which operates your tree’s 7 function lighting 
capability.
Your tree should include the following components:
A folding metal tree stand with (3) eyebolts.
An ON/OFF push button foot pedal with cord and plug (Fig 6); 
which is pre-attached at the lowest section of your tree (Fig 5). 
The 5’ tree will have (2) tree sections. The 6.5’ and 7.5’ trees will 
have (3) tree sections; (“A”,  “B” and “C”; as shown in Fig 5). 
The 9’ tree will have (4) tree sections “A”,  “B”,  “C” and “D”. 

Thank you for your purchase of this pre-lit & pre-shaped 
Christmas tree.
With proper use and care, this tree will provide years of 
trouble-free enjoyment. 
Please follow the instructions below in order to effectively 
assemble and disassemble your tree. 
In the event that you should encounter any issues during 
the assembly of your tree; please refer to the 
“Troubleshooting” portion of this manual or call our toll free 
customer service number at 1-888-831-6656, and a trained 
representative will assist you. 
Customer service hours of operation: 
Monday-Friday: 8:00am – 4:30pm CST. 
Holiday weekends: 
Last weekend in November: 8:00am – 4:30pm CST.
First weekend in December: 8:00am – 4:30pm CST.    
Visit us on the web at www.santasbest.com 

PRE-LIT & PRE-SHAPED CHRISTMAS TREE

ASSEMBLY OF THE TREE STAND

1. Remove the tree stand from the plastic bag, loosen the eye

bolt and open the tree stand to form an “X”.

2. Align the holes for the insertion of the remaining (2)

eyebolts.

3. Insert each eyebolt and begin threading in a clockwise

direction for a couple of rotations only; leaving enough
room for the tree’s pole from section “A” to be inserted into
the assembled stand (Fig 2).

4. Place the tree stand in its desired location; as once the tree is

fully assembled, it may be too difficult to move and relocate.

4. Carefully cut the nylon strapping bounding the branches

upright.
CAUTION: Be extremely careful not to cut any of the exposed
light set wires.

5. Now gently guide the branches downward into place.
6. Beneath the canopy of section “A”, contains an push button

foot pedal with cord and plug (Fig 6). 

Remove the twist-tie binding the cord together and insert

the plug into a working electrical outlet.

7. On/off push button foot pedal operation:

The on/off push button foot pedal is intended to provide

basic manual on/off operation only; and therefore cannot
provide the remote control’s 7 function lighting capability. 

Riverwoods, IL 60015 USA
www.santasbest.com

2. If failure to light persists, press the push button foot pedal; as it

may be in the “Off” mode.

3. If the top of the tree or another individual lettered section does

not illuminate, remove each section and then reinsert as

instructed, to ensure the electrical connection is made. 

NOTE: The tree’s top is designed specifically for a secure and

firm connection point. Downward force will be needed to

ensure that the electrical connection occurs.

4. Always inspect your tree for any burned out LED bulbs. 

Although the tree will continue to remain lit even if a bulb

burns out, is loose or is missing; any burned out LED bulbs

should be replaced promptly to ensure the performance and

life expectancy of your tree.

5. If lighting is out of sequence after replacing an LED, remove

and re-insert the LED making sure to align the husk tabs as

illustrated in the safety instruction sheets. This is a specialty

bulb. Do not replace with a standard LED or Incandescent bulb. 

Should you need additional bulbs please call our customer

service department at 1-888-831-6656.

Made in China    Printed in China

This is not a toy, for decorative use only.

NOTE: DO NOT USE A DIMMER SWITCH, INSTALL ANY

ADDITIONAL LIGHTING OR ORNAMENTION THAT IS

POWERED THROUGH THE LIGHT BULB SOCKETS. DOING

THIS MAY RESULT IN DAMAGE TO THE LIGHTING SYSTEM

OR MAY CAUSE PERSONAL INJURY; THEREFORE VOIDING

THE LIMITED WARRANTY PROVIDED WITH THIS PRODUCT.

1. Gently remove the plug from its electrical outlet, and carefully bind 

the cord which contains the push button foot pedal and plug.

2. Beginning with the tree’s top section; lift each section straight

up from the section below, and continue working downward. 

NOTE: You may have to slightly wiggle each section as you lift

each section upward.

3. To remove the bottom and final section; loosen the eyebolts by

turning in a counter-clockwise direction and lift section “A” 

from the support collar of the tree stand.

4. Gently fold the branches of each section upward, towards the

center, and position in the storage container.

NOTE: With the exception of the tree’s “top” section; by holding

each section upside down; the branches will collapse down-

ward, due to the hinging, aiding in the packing of each section

into the storage container.

5. Fully unthread the eyebolts from the tree’s stand and fold

together; placing in the storage container.

6. It is recommended to always store the tree in a cool, dry

location protected from excessive exposure to heat or sunlight. 

NOTE: Store your remote control in a SAFE & DRY location and

remove the battery from remote control before storage.

DISASSEMBLY & STORAGE

NOTE: ALTHOUGH THE LED LIGHT STRINGS ON THE TREE ARE

RATED FOR INDOOR OR OUTDOOR USE; THE COMBINATION

OF THE TREE WITH THE LED LIGHTS IS RECOMMENDED FOR

INDOOR USE ONLY.

Fig 2

10. Once section “B” is fully inserted downward into section “A”; 

both section “A” and section “B” will now be lit.

11. Again, carefully cut the nylon strapping bounding the

branches upright; being extremely careful not to cut any of
the exposed light set wires.

12. Now gently guide the branches of section “B” downward

into place.

13. Depending on the height of the tree you have purchased, 

you will continue to build your tree upwards, section by
section, following the above steps until the tree is
completely assembled. Each section of the tree is labeled in
alphabetical order beginning from the bottom to the top.

8. Locate the next section of the tree which is identified by a

label on the outer branches marked “B” (Fig 5).

9. Remove the protective plastic cap by twisting and pulling it

from the end of the pole on section “B”; insert that end onto
the top of the pole of section “A” (Fig 4).

Fig 4

EZ-POWER™ TECHNOLOGY

NOTE: Your tree has been designed with EZ-Power™ 
technology; allowing for each of the tree’s remaining 
sections to light up automatically, upon a firm insertion of 
each lettered section (Fig 5).

CCT15

Patent No. : RE43,890E, 8,836,224 and other patents pending.

Fig 6

• Steady Multi
•  Steady White
• Steady Pastel
• Slow Fade White to Multi
• Flash White to Multi
•  Slow Twinkle
•  Fast Twinkle

REMOTE CONTROL OPERATION

Contained in the poly-bag; which is adhered to the interior flap 

of the tree’s carton, is your remote control that operates your 

tree’s 7 lighting functions.
Before operation; a standard 9 volt type battery (6F22, 6LR61 or 

23F6-220) must be installed into the remote control; by simply 

removing the slide plate located on the back of the remote 

control.  
The remote controls the 

following 7 functions as well as 

the ON/OFF operation. To change 

the functions, simply press the 

“Function    ” or “Function     ” to 

cycle through each function. 

NOTE: If the tree is powered off by 

the use of the push button foot 

pedal, remote control or by 

unplugging it from the electrical 

outlet; when powered back on the 

tree will resume the memory of 

the last lighting function selected.

TROUBLESHOOTING

1. If the tree does not illuminate press the function button on

your remote control. If failure to light persists the battery may

need to be replaced. Insert a standard 9 volt type battery (6F22, 

6LR61 or 23F6-220); aligning the appropriate ( +/- ) markings

accordingly.

NOTE: The tree’s 7 function lighting capability is controlled

solely by the use of the remote control provided. 

If the tree fails to light due to a damaged or defective remote

control; please resort to manual push button foot pedal

operation until a new remote control can be provided through

our customer service center.

Fig 1

A

B

C

Foot Pedal

Fig 5

18”

2015 QVC
Heritage Spruce Instruction Sheet - 7 Function Remote (English)
Date:  5/27/15

15”

Item # 7245015-IP66QV (7.5ft Heritage Spruce)
             7245016-IP66QV (5ft Heritage Spruce)
             7245017-IP66QV (6.5ft Heritage Spruce)
             7245018-IP66QV (9ft Heritage Spruce)

Summary of Contents for CCT15

Page 1: ...enjoyment Please follow the instructions below in order to effectively assemble and disassemble your tree In the event that you should encounter any issues during the assembly of your tree please refer to the Troubleshooting portion of this manual or call our toll free customer service number at 1 888 831 6656 and a trained representative will assist you Customer service hours of operation Monday ...

Page 2: ...n only and therefore cannot provide the remote control s 7 function lighting capability 10 Once section B is fully inserted downward into section A both section A and section B will now be lit 11 Again carefully cut the nylon strapping bounding the branches upright being extremely careful not to cut any of the exposed light set wires 12 Now gently guide the branches of section B downward into plac...

Page 3: ...h function NOTE If the tree is powered off by the use of the push button foot pedal remote control or by unplugging it from the electrical outlet when powered back on the tree will resume the memory of the last lighting function selected TROUBLESHOOTING 1 If the tree does not illuminate press the function button on your remote control If failure to light persists the battery may need to be replace...

Page 4: ...E TO THE LIGHTING SYSTEM OR MAY CAUSE PERSONAL INJURY THEREFORE VOIDING THE LIMITED WARRANTY PROVIDED WITH THIS PRODUCT 1 Gently remove the plug from its electrical outlet and carefully bind the cord which contains the push button foot pedal and plug 2 Beginning with the tree s top section lift each section straight up from the section below and continue working downward NOTE You may have to sligh...

Reviews: