background image

 

 

A4b Automatic Dispenser                                                       

  V1.0                                                                                           

9). During working time of dispenser, please do not put your hand into the dispenser to avoid hurt of the 

punch head; please do not touch the punch head while out of use.     

10).During  transportation,  the  machine  should  be  leveled,  preventing  from  being  shocked,  pressed,  and 

bottomed up  or side faced on  the ground.    The machine  should be kept in ventilated and dry room 

which is moisture-proof, fire-proof. 

11). It is forbidden to work the machine in the inflammable and explosive environment.

   

12). The dismantling procedures  of  the  fixing screws are as  follows if you need  to remove the machine 

from the foundation.     

 

 

 

 

 

13). Take out the mouse seat and the two M5X12 inner hexagon screw. Put the Ф5 flat washer and  spring 

washer on it. Then fix the mouse seat onto the machine.   

 

 

 

 

 

 

 

4. Machine Composition 

                                   

                       

 

Use  17-19  solid  spanner  to 

remove  the  screws  of  the 

both sides.   

 

注意:左右共两处

 

 

Mouse Seat 

 

Inner Hexagon Screw 

M5X12

with Ф5 flat 

washer and spring 

washer

 

 

Summary of Contents for A4B Series




















Reviews: