background image

7

Instruction Manual for SABER MAGNET 24V

1-888-726-8869

www.sanuvox.com

MAINTENANCE

How to Replace Lamp(s)

Replacing lamp on the SABER MAGNET 24V is quick and easy. Simply turn off the power source, remove lamp from duct, 

dispose of old lamp and replace with new Sanuvox branded UV lamp, replace lamp in duct and turn power source back on. See 

below for detailed step by step instructions.

 CAUTION:

 In order to avoid reduced performance of lamp(s), do not touch lamp glass without gloves.

Step by Step Lamp Replacement

1.  First  disconnect  white  socket  from  the  old  lamp. Then,  loosen  the  2 

screws on the retainer ring and turn retainer ring counterclockwise  . 

Pull out the old lamp. Dispose of old lamp.

 

NOTE: 

UV lamps can be disposed/recycled after use, as any other 

fluorescent lamps. Contact and follow your local and national authorities’ 

specific instructions.

2. 

Prepare the new lamp.

 Remove the contents from packaging. Only 

after you have visually inspected the UV lamp should you cut open the 

packaging.

3.  Carefully slide the new 

UV lamp

 out from the cardboard sleeve. Be sure 

to wear the 

cotton gloves

 (included) guaranteeing a clean lamp free 

from fingerprints. Fingerprints on the lamp will negatively impact the UV 

output of the lamp.

STEP 1

STEP 2

STEP 3

4.  Place the new lamp in the duct. Tighten the 2 screws on the retainer ring 

and turn retainer ring right. Connect white socket from the new lamp.

 

Then, reset your product and its lamp timer (see page 8).

STEP 4

How to Clean your Product

For optimal performance, the lamp(s) should be kept free of dust and residue deposit: clean every two to three months with a 

soft tissue and mild soap or alcohol based solution. Always spot test the cleaner to make sure it does not damage the surface.

 CAUTION:

 Under no circumstance should water be sprayed or splashed onto the product.

STORAGE

The SABER MAGNET 24V is an in-duct unit working continuously and automatically and therefore, requires no specific storage.

Summary of Contents for SABER MAGNET 24V











Reviews: