manualshive.com logo in svg

Sanwa MT-4, Operating Manual

The Sanwa MT-4 is a top-of-the-line radio control transmitter for RC enthusiasts. With its user-friendly interface and advanced features, this premium product brings precision and control to your RC experience. Enhance your understanding of this incredible device by downloading the free operating manual from our website.

Share
Download
background image

Page 2

PACKAGING

The packaging of your SANWA 

MT-4 2.4GHz FHSS-4T

 radio control system has been specially designed for the safe transportation 

and  storage  of  the  radio  control  system's  components. 

After  unpacking  your  radio  control  system,  do  not  discard  the 

packaging materials

. Save the packaging materials for future use if you ever need to send your radio control system to us for 

service or to store your radio control system if you don't plan on using it for an extended period of time.

Introduction ............................................................................................................................................................................Page 3

 

Safety ..............................................................................................................................................................................Page 3

TABLE OF CONTENTS

Usage Precautions ................................................................................................................................................................Page 4

 

2.4GHz Frequency Band Precautions .............................................................................................................................Page 4

 

Transmitter Precautions ...................................................................................................................................................Page 4

 

Receiver Precautions ......................................................................................................................................................Page 4

 ..................................................................................................................................................Page 5

 

System Features .............................................................................................................................................................Page 5

 

 .....................................................................................................................................................Page 5

 

Servo Recommendations ................................................................................................................................................Page 5

Features Familiarization ........................................................................................................................................................Page 6

 

Transmitter Features Diagrams .......................................................................................................................................Page 6

 

Receiver Features Diagram .............................................................................................................................................Page 8

 

Transmitter and Receiver Features Descriptions .............................................................................................................Page 8

 

Servo Connectors ............................................................................................................................................................Page 9

 

Transmitter Safety Alarms and LED Condition Indicators ................................................................................................Page 9

System Connections............................................................................................................................................................Page 11

 

Transmitter Battery Options ...........................................................................................................................................Page 11

 

Alkaline Battery Installation ...........................................................................................................................................Page 11

 

Transmitter Battery Charging Options ...........................................................................................................................Page 11

 

Warnings if Using Li-Po or Li-Fe/A123 Transmitter Batteries ........................................................................................Page 11

 

Receiver Connections and Mounting .............................................................................................................................Page 12

 

Telemetry Connections and Mounting ...........................................................................................................................Page 13

Adjustments and Options ....................................................................................................................................................Page 14

 

Throttle Trigger Position Adjustment ..............................................................................................................................Page 14

 

Throttle Trigger Angle Adjustment .................................................................................................................................Page 14

 

Grip ................................................................................................................................................................................Page 14

 

Throttle Trigger and Steering Wheel Spring Tension Adjustment ..................................................................................Page 15

 

Steering Wheel Travel Adjustment ................................................................................................................................Page 15

 

Wrist Strap Anchor .........................................................................................................................................................Page 15

LCD and Programming Keys ...............................................................................................................................................Page 16

 

Top Screen and Telemetry Screen Overview ................................................................................................................Page 16

 

Programming Keys Overview and Functions ................................................................................................................Page 17

Transmitter and Receiver Binding .......................................................................................................................................Page 18

Programming Menus ...........................................................................................................................................................Page 19

 

Overview (Includes Complete Programming Menu List) ...............................................................................................Page 19

System Menus .....................................................................................................................................................................Page 51

 

Overview (Includes Complete System Menu List) .........................................................................................................Page 51

Reference ............................................................................................................................................................................Page 73

 

Troubleshooting Guide ...................................................................................................................................................Page 73

 

Glossary of Terms ..........................................................................................................................................................Page 74

 

Index ..............................................................................................................................................................................Page 79

 

Notes .............................................................................................................................................................................Page 87

Features and Specifications

System Specifications

Summary of Contents for MT-4































Reviews:

No comments

Related manuals for MT-4

Warner Electric MCS202-E1 User Manual preview
MCS202-E1
Brand: Warner Electric Pages: 3
iCeeO2 C30 Instruction Manual preview
C30
Brand: iCeeO2 Pages: 7
SABAF 10 Instructions For Use, Maintenance Instructions preview
10
Brand: SABAF Pages: 6
HandyTrac Key Control Easy Manual Installation And Operation preview
Key Control
Brand: HandyTrac Pages: 14
TA STA Quick Start Manual preview
STA
Brand: TA Pages: 6
Parkside PDWE 8 A1 Instructions Manual preview
PDWE 8 A1
Brand: Parkside Pages: 86
TANDBERG Maestro MXP Installation Sheet preview
Maestro MXP
Brand: TANDBERG Pages: 2
TANDBERG 6000 MXP Profile Quick Start Manual preview
6000 MXP Profile
Brand: TANDBERG Pages: 2
TANDBERG 3000 MXP Profile Connecting Manual preview
3000 MXP Profile
Brand: TANDBERG Pages: 2
TANDBERG 2000 MXP Short User Manual preview
2000 MXP
Brand: TANDBERG Pages: 11
TANDBERG Media Processing System MPS 800 User Manual preview
Media Processing System MPS 800
Brand: TANDBERG Pages: 106
TANDBERG C20 PLUS User Manual preview
C20 PLUS
Brand: TANDBERG Pages: 44
TANDBERG 150 MXP Installation preview
150 MXP
Brand: TANDBERG Pages: 2
TANDBERG MXP Short User Manual preview
MXP
Brand: TANDBERG Pages: 11
Madison AV PC2 Reference Manual preview
PC2
Brand: Madison AV Pages: 2
XtendLan KEYBPTZ4D Operating Instructions Manual preview
KEYBPTZ4D
Brand: XtendLan Pages: 12
ZBA ZZB88-441S User Manual preview
ZZB88-441S
Brand: ZBA Pages: 27
M-system R7C-RS4 Instruction Manual preview
R7C-RS4
Brand: M-system Pages: 10

Brands by name

Popular brands

Load more brands