background image

 

 

Introduction 

Thank you for choosing this product. This document contains important safety 
precautions for users and service technicians.To ensure proper operation and 
reliability throughout the useful life this device, read this manual prior to use and 
keep it nearby for future reference. 

 
 
 

Safety Precautions

 

 

Read this manual carefully before installing, operating, performing maintenance, or 
inspecting this device in order to understand all instructions and related safety 
precautions. 

 

Usage and Storage Precautions 

 

Never operate or store the equipment in the following environmental 
conditions, as doing so may cause malfunction, damage or deterioration, 
which could result in fire and/or injury: 

z

 In ambient environmental conditions other than those specified 

(temperatures outside the range of 0 to 40°C (32 to 104°F), and relative 
humidity outside of the range of 30% to 90%). 

z

  Where the device is exposed to direct sunlight. 

z

  Where the equipment is directly exposed to heat from a heat source, such 

as a stove. 

z

  Where the device may be subject to vibration or physical shock. 

z

  Near a device that may emit sparks. 

z

  In the presence of dust, salt, or corrosive or flammable gas. 

z

 Outdoors. 

 

 

 
 
 

CAUTION

Summary of Contents for A11F102 Series












Reviews: