Sanyo Denki ASD 100S2NU Installation & Maintenance Manual Download

Page: 2 / 32

Introduction

Thank you for your purchasing of this equipment (UPS).

SAVE THESE INSTRUCTIONS

This Manual contains important information for Model ASD“ ”U that should be followed
during installation and maintenance of the UPS and batteries.
Read this manual to work safely, and to use the UPS correctly before the work of installation
and maintenance.

This unit is intended for installation in a temperature-controlled, indoor area free of conductive
contaminants.

･

Operating temperature: 0 to 40

℃

UPS is an abbreviation of Uninterruptible Power Supply.

Table of contents

1 Safety

precautions

.....................................................

Notes for correct operation ..................................................... 6

2.1

Notes for input power supply

......................................

2.2

Notes for installation

.....................................................

2.3

Notes for handling

.....................................................

2.4

Setting of frequency

.....................................................

Confirmation of packing content

......................................

4 Outline

.....................................................

Outside dimensions and part names

......................................

5.1 Equipment

..................................................... 9

5.2

LCD, LED panel

.....................................................

5.3 Auxiliary

switch

..................................................... 11

5.4

Outside inter face

.....................................................

6 Installation

.....................................................

6.1 Environment

..................................................... 14

6.2 Delivery

..................................................... 14

6.3 Installation

space

..................................................... 14

6.4

Installation of equipment

.....................................................

7 Wiring

.....................................................

7.1

Wiring of terminal block

.....................................................

7.2 Connection

terminal block wiring

......................................

7.3

Connection of outside interface

......................................

8 Preparations

before

operation ......................................

9 Operating

procedures .....................................................

9.1

Starting of operation

.....................................................

9.2

Power failure operation check test

......................................

9.3

Stopping of daily operation ..................................................... 21

Maintenance and inspection .....................................................

10.1 Daily

inspection

..................................................... 22

10.2 Periodic

inspection

..................................................... 22

10.3 Replacement

parts

..................................................... 22

10.4 Maintenance of battery .....................................................

10.5 Replacement of battery .....................................................

Power Supply Maintenance Bypass

......................................

11.1 Switching the Supply from the Inverter to Maintenance Bypass

...... 25

11.2 Switching from Maintenance Bypass to Inverter Power

......

At sounding buzzer

.....................................................

Operation at emergency

.....................................................

14 Specifications

.....................................................

Guarantee of equipment

.....................................................

■

SANYO DENKI Co., Ltd. Head office, branch offices

Summary of Contents for ASD 100S2NU

































Search results

Summary of Contents for ASD 100S2NU

Reviews:

Related manuals for ASD 100S2NU

Brands by name

Popular brands

Sanyo Denki ASD 100S2NU, Installation & Maintenance Manual

Search results

Summary of Contents for ASD 100S2NU

Reviews:

Related manuals for ASD 100S2NU

Brands by name

Popular brands