background image

INSTRUCTION  MANUAL

MICROCOMPUTER  CONTROL
FULLY AUTOMATIC WASHING MACHINE

MICROCOMPUTER  CONTROL
FULLY AUTOMATIC WASHING MACHINE

ASW-A100HT

Before operating this washing machine, please read 
these instructions carefully and completely.

Before operating this washing machine, please read 
these instructions carefully and completely.

 

WARNING - This appliance must be earthed.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:
 

   

Green/yellow: Earth               

Blue: Neutral             Brown: Live

 
As the colours of the wires in the mains lead of this appliance may not correspond 
with the coloured markings identifying the terminals in your plug, proceed as follows:

Light 

The wire which is coloured green and yellow must be connected to the terminal 

   

in the plug which is marked with the letter E or by the earth symbol       

   

or coloured green or green and yellow. 

The wire which is coloured  light blue must be connected to the terminal which is 

   marked with the letter N or coloured white. 

The wire which is coloured brown must be connected to the terminal which is marked 

   

with the letter L or coloured black.

● 

● 

● 

SPECIFICATIONS

SPECIFICATIONS

CODE NO.301-6-411S-972-40B

CODE NO.301-6-411S-972-40B

610(W) x 585(D) x 1000(H) mm 

6

0 litres

AC Local voltage 

 

Dimensions 

Power Source

Water level (HIGH)

Power Consumption 
Required Water Pressure

2

FOR WASHER PLUG TOP 3 PIN

● If the 2-pin type of socket-outlet has a grounding terminal, 
   securely attach the end of the Grounding Wire to the 
   terminal. 
● When grounding the washer, connect the grounding wire 
   before plugging in the Power Cord. 
● If the 2-pin type of the socket-outlet has no grounding 
   terminal, consult your nearest dealer or securely attach 
   the end of Grounding Wire to a suitable grounding point, 
   such as a metal cold water pipe. 
   Never connect the Grounding Wire to a gas pipe. 
● Unplug the Power Cord before disconnecting the 
   Grounding Wire.

For BS Standard Plug With A 13 Amp Fuse

(                                                                     )

Grounding
Terminal

Grounding 
Wire Of 
Washer

Grounding 
Wire

Grounding 
Rod

FOLLOWING CAUTIONS ARE FOR WASHER USING DOUBLECORE 
CORD ONLY.

SANYO Electric Co.,Ltd.

SANYO Electric Co.,Ltd.

400 W 
0.03 MPa ~ 1.0MPa 
(0.3 kgf/cm  ~ 10 kgf/cm ) 

2

Summary of Contents for ASW-A100HT











Reviews: