background image

 

 

15

3.10

 

Installing Handrail and Bumper 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
Attaching the Bumper 
1.

 

Attach Maintenance Bumper (length 39-3/8 inches) to Bumper Brackets over the electrical 
connection box (“Raceway”) on each SANYO Case. The Raceway is located on the right end of each 
SANYO Case. 

2.

 

Attach Full-Length Bumpers between Maintenance Bumpers on separate SANYO Cases, and also 
between Maintenance Bumpers and Patch Ends. 

3.

 

Cut Full-Length Bumpers to size on-site. Cut to correct size so that no gaps remain between pieces. 

 

Attaching the Handrail 
1.

 

Starting at one end of SANYO Case line-up, attach pieces of Handrail to Handrail Retainer, butting 
the pieces end-to-end without gaps. 

2.

 

When you reach the final piece of Handrail to be installed between the last SANYO Case in the 
line-up and the Patch End, cut that piece to length so there are no gaps between Handrails or 
between Handrails and Patch Ends. 

3.

 

Cut Handrail to size on-site. Cut to correct size so that no gaps remain between pieces. 

 
 
 

 

WARNING!

 

Wear appropriate eye and hand protection and exercise care when using powered tools to prevent personal injuries and 
damage to the case. 

 

 

 

 

Summary of Contents for CVW-EXA124































Reviews: