background image

HOW TO HANDLE THE

Insert a disc into the CD magazine with the label side up.

Take out a disc.

1. When a disc is inserted into the magazine, the push out

knob for that slot will be raised (fig.2).

2. Press down on the push-out knob (fig.2).

3. Remove the disc by holding the edge as shown (fig.3).

Notes

Avoid touching the playing side of the disc.

Only one disc can be inserted into each slot of the CD

magazine. Do not try to insert two discs into one slot.
Doing so can damage the magazine and the discs.

When playing an 8cm disc, a separately available mag-

azine (MGN-12 06) should be used instead of using the

adaptor. 

The 

 disc adaptor must never be used,

or the internal mechanism may break.

OPERATION-INSERTING THE MAGAZINE

Slide the door to the right side of the unit, until it locks

 place.

INSERTING THE MAGAZINE

Be sure that the top of the magazine is up, and gently
insert it into the unit, until it clicks into place.

REMOVING THE MAGAZINE
Push in the eject switch. After a few seconds the maga-

zine 

will eject from the unit. Remove the magazine.

N o t e
Be sure to slide the door closed, after the magazine has
been installed. If the door is left open, dust could enter

the unit causing a malfunction.

CD MAGAZINE

CD ma

de up and playing side

One disc in each slot 

 discs)

Taking out a disc

Part A (Push-out knob)

Fig.2

Fig.3

Door

Eject switch

Summary of Contents for FXD-C200










Reviews: