Sanyo MDF-393 Service Manual Download

Page: 26 / 34

11. Prevention for oil logged in the capillary

Purpose:

Capillary heater is conducted electricity by regularly turning both L/H side compressor off to
prevent oil logged in the capillary.

Operation:

Both L/H side compressor are turned off, while the capillary heater relay is turned on.

Frequency:

8 minutes in every 18 hours (Minutes are changeable in F19)

Timing of operation:

(1) About 9 seconds after both L/H side compressors are turned off during cycle operation.
(2) Both L/H side compressors are forcibly turned off if they keep running for 60 minutes or

more after they were ordered to turn off.

Operation of capillary heater:
Capillary heater is forcibly ON/OFF controlled in F18.

12. Sensor

offset

Sensor offset value:
(1) Temperature sensor: +1.3

㷄

(Changeable in F07)

(2) Cascade sensor: +/-0.0

㷄

(Changeable in F08)

(3) Filter sensor: +/-0.0

㷄

(4) AT sensor: +/-0.0

㷄

13. Remote alarm terminal

Operation:
Once the alarm is triggered, the remote alarm contact (RLY2) switches the position.

CN3

1 – 2 (N.O.) 1 – 3 (N.C.)

Normal Open Close
In alarm

Open

14. Power

reset

Setting values after the power is reset:

Alarms: OFF
Compressors: OFF

㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷

Remote alarm: OFF

㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷

Alarm resume time: 30 minutes

㩷㩷㩷㩷㩷㩷㩷

Door alarm delay time: 2 minutes

㩷㩷㩷

Timers: Reset
Counting for L side compressor OFF period: Reset
Setting data: Referred to non-volatile memory

Momentary power failure:

Status of the unit should be diagnosed by comparing the chamber temperature with

the set temperature. When the chamber temperature is equal or lower than the set
tempe10

㷄

, it diagnoses as ‘Momentary power failure’.

Setting values after power retrieves from power failure:

Alarms: OFF
Compressors: OFF

㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷

Remote alarm: ON

㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷

Timers: Reset
2H timer, 8H timer: 0 (Reset)
Counting of period Low side compressor turns off: Reset

Summary of Contents for MDF-393



































Search results

Summary of Contents for MDF-393

Reviews:

Related manuals for MDF-393

Brands by name

Popular brands

Sanyo MDF-393, Service Manual

Search results

Summary of Contents for MDF-393

Reviews:

Related manuals for MDF-393

Brands by name

Popular brands