background image

58

19 

 

 

      CHANGE OF COMPRESSOR DELAY TIME 

 

The delay time of high and low stage side compressor can be changed to reduce the load on the power 

line and to facilitate the start-up (reset) of the freezer after power failure. 

 

The example in the table is based on the assumption that the delay time is changed to 4 minutes. 

(The delay time is set in 2 minutes at the factory.)

 

 

Note:

 

• The delay time should be the same for high stage side and low stage side compressors. 

• The setting range for delay time is between 2 and 15 minutes.    The cool down of chamber temperature 

may be slow when the setting of delay time is over 5 minutes, depending on the installation environment.   

There is no need of changing the delay time when the capacity of power source is adequate. 

 

Table 8.    Changing procedure for delay time (change from 2 minutes to 4 minutes)

 

 

Description of operation 

Key operated

Indication after operation 

1  

---- 

The current chamber temperature is 
displayed. 

Press numerical value shift key for 

5 seconds. 

 

 

The first digit is flashed. 

Set the figure to F05 with the 
numerical value shift key. 

 

When pressed, the figure of settable   

digit changes. 

4  Press SET key. 

SET 

The current delay time is displayed. 

The first digit is flashed. 

Set the figure to 004 with the 

numerical value shift key. 

 

When pressed, the figure of the first 
digit changes. 

6  Press SET key. 

SET 

The delay time is memorized and   
the current chamber temperature is   
displayed. 

• The compressor starts to operate with the delay time set by the above procedure at the time of power on 

or after power failure.  However, the start up of the low stage side compressor is affected by the 

chamber temperature and the cascade condenser temperature.  The delay time varies depending on 

how they meet the start up conditions. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for MDF-U5386S






































Reviews: