- 49 -
Service Adjustment
Group/
Item
Item Name
Function
Initial
Range Note
162 PreCoast YCbCr 1080i 60Hz
7
0 - 63
163 PostCoast YCbCr 1080i 60Hz
13
0 - 63
164 PreCoast YCbCr 1080i 50Hz
7
0 - 63
165 PostCoast YCbCr 1080i 50Hz
13
0 - 63
166 PreCoast YCbCr 1035i
7
0 - 63
167 PostCoast YCbCr 1035i
13
0 - 63
180 PreCoast SCART 480i
7
0 - 63
181 PostCoast SCART 480i
13
0 - 63
182 PreCoast SCART 575i
7
0 - 63
183 PostCoast SCART 575i
13
0 - 63
Group 10
Sync Processor
0 SYNCAMPHLCKTOLOW
Minimum sync amplitude threshold
for HLCK 1 to 0 tansition
0x1000
0 - 9999
1 SYNCAMPHLCKTOHI
Minimum sync amplitude threshold
for HLCK 0 to 1 tansition
0x700
0 - 9999
Group 20
Video Decoder
*R : Read Only Value
0 Y Level
Composite / S-Video - Y Level (ADC
RGB Gain)
10 / 10
0 - 255
Composite / S-Video
* Gain Adjustment [Video]
1 C Level
Composite / S-Video - C Level (ADC
Saturation)
115 / 115
0 - 255
Composite / S-Video
2
3 XCXL Level
Cross-Chroma, Cross-Luma Level
3
0 - 5
4 C2DNBANDWIDTH
Comb 2D Narrow Bandwidth
3 / 3
0 - 3
NTSC/PAL
5 C2DWBANDWIDTH
Comb 2D Wide Bandwidth
4 / 4
0 - 7
NTSC/PAL
6 C2DCNMINLEAK
Comb 2D Chroma Narrow Band
Minimum Leakage
0 / 3
0 - 3
Left Values are adjustable if CXCL Level
= 5.
7 C2DCNSLOPELEAK
Comb 2D Narrow Band Slope
Leakage
7 / 7
0 - 7
NTSC/PAL
8 C2DCWMINLEAK
Comb 2D Wide Band Minimum
Leakage
1 / 3
0 - 3
NTSC/PAL
9 C2DCWSLOPELEAK
Comb 2D CW Slope Leakage
6 / 6
0 - 7
NTSC/PAL
10 COMBLEAK2BPGAIN
Comb Leak To Ban Pass Gain
1 / 0
0 - 3
NTSC/PAL
11 C2DBDIAGONALGAIN
Comb 2D Band Pass Diagonal Gain
1 / 3
0 - 3
NTSC/PAL
12 C2DNBCWBCLGAIN
Comb 2D Narrow Band Comb Wide
Band Comb
1 / 1
0 - 3
NTSC/PAL
13 RLUMASETUP-Enable
7.5IRE Setup Enable
0
0 - 1
Effective only NTSC Signal
Group 40
General
0 IP Mode
Sets for IP Off
1
0 - 1
0: IP Block not used
1: IP OFF used with IP Block
1 3:2 PullDown Mode
1
1 - 3
bit0 : Global Motion
bit1 : Video Motion
2 Detect Film Mode Enable
0
0 - 2
0 : 2:3pull down & 2:2pull down
1 : 2:3pull down
2 : 2:2pull down
3 Force IP Mode
2
0 - 2
0 : IP Process Disable
1 : Force Normal IP Mode
2 : Force Film Mode
Effective only for PSF Signal.
Group 41
Deinterlacer setting
Effective only for Progressive ON-L1 mode.
0 Motion Adaptive Weight Value
<KDEINT>
60
0 - 255
1 Angle Interpolation Level
0 : Conservative <====> 4 :
Aggressive
4
0 - 4
2 CUE Low Pass Filter Enable
<CUELPFEN>
0
0 - 1
Group 42
Deinterlacer setting
Effective only for Progressive ON-L2 mode.
0 Motion Adaptive Weight Value
<KDEINT>
0
0 - 255
1 Angle Interpolation Level
0 : Conservative <====> 4 :
Aggressive
2
0 - 4
2 CUE Low Pass Filter Enable
<CUELPFEN>
0
0 - 1
Group 43
Deinterlacer setting
Effective only for Progressive ON/Film mode.
0 Motion Adaptive Weight Value
<KDEINT>
30
0 - 255
1 Angle Interpolation Level
0 : Conservative <====> 4 :
Aggressive
4
0 - 4
2 CUE Low Pass Filter Enable
<CUELPFEN>
0
0 - 1
Group 45
Noise Reduction (Time)
Effective only for N.R - Off
0 Noise Pixel Range
<NSRANGEY> / <NSRANGEUV>
1
0 - 2
1 Noise Region 0
<NSREGIONY0> / <NSREGIONUV0>
12
0 - 1023
2 Noise Region 1
<NSREGIONY1> / <NSREGIONUV1>
24
0 - 1023
Summary of Contents for PLC-XE50
