background image

20

English

WARNING

!

Be sure to comply with local codes on running
the wire from the indoor unit to the outdoor unit
(size of wire and wiring method, etc.).

!

Each wire must be firmly connected.

!

No wire should be allowed to touch refrigerant
tubing, the compressor, or any moving part.

!

Be sure to connect power wires correctly
matching up numbers on terminals of the 
outdoor unit and respective indoor units A – D.

CAUTION

!

Be sure to connect the power supply line to the
outdoor unit as shown in the wiring diagram.
The indoor unit draws its power from the 
outdoor unit.

!

Do not run wiring for antenna, signal, or power
lines of television, radio, stereo, telephone,
security system, or intercom any closer than 
1 meter from the power cable and wires between
the indoor and outdoor units. Electrical noise
may affect the operation.

!

To avoid the risk of electric shock, each air
conditioner unit must be grounded.

!

For the installation of a grounding device,
please observe local electrical codes.

!

Grounding is necessary, especially for units
using inverter circuits, in order to release
charged electricity and electrical noise
caused by high tension.
Otherwise, electrical shock may occur.

!

Place a dedicated ground more than 2 meters
away from other grounds and do not have it
shared with other electric appliances.

WARNING

Fig. 25b

4 indoor units with SAP-CMRV2446, CMRV3146

INDOOR  UNIT

4

3

2

1

3

2

1

2

1

UNIT  A

Ter

mi

n

al

L

N

A

B

C

Termi

n

al (9P)

Termi

n

al

(2P)

OUTDOOR  UNIT

Gro

un

di

ng

 li

n

e

INDOOR  UNIT

4

3

2

1

6

5

4

UNIT  B

Ter

mi

n

al

Gro

un

di

ng

 li

n

e

INDOOR  UNIT

4

3

2

1

9

8

7

UNIT  C

Ter

mi

n

al

Gro

un

di

ng

 li

n

e

Gro

un

di

ng

  li

n

e

P

ow

er  

su

pply

S

i

ng

le-pha

s

e  220-240V

A

C  50Hz

                       220V

A

C  60Hz

(A)

(B)

(B)

(C)

(B)

(B)

(C)

(B)

(B)

(C)

9

8

7

6

5

4

3

2

1

1

2

L

N

Termi

n

al (12P)

Termi

n

al

(2P)

OUTDOOR  UNIT

Gro

un

di

ng

 li

n

e

Gro

un

di

ng

 li

n

e

Gro

un

di

ng

 li

n

e

Gro

un

di

ng

 

li

n

e

INDOOR  UNIT

4

3

2

1

UNIT  A

UNIT  B

UNIT  C

UNIT  D

12

11

10

Ter

m

i

n

al

A

INDOOR  UNIT

4

3

2

1

Ter

m

i

n

al

B

INDOOR  UNIT

4

3

2

1

Ter

m

i

n

al

C

INDOOR  UNIT

4

3

2

1

Ter

m

i

n

al

D

Gro

un

di

ng

  li

n

e

P

ow

er 

 

su

pply

S

i

ng

le-pha

s

e  220-240V

A

C

  50Hz

                       220V

A

C  60Hz

(A)

(B)

(B)

(C)

(B)

(B)

(C)

(B)

(B)

(C)

(B)

(B)

(C)

3 indoor units with SAP-CMRV1936

5-3. Wiring System Diagram

Ter

mi

n

al

INDOOR  UNIT

4

3

2

1

3

2

1

6

5

8

7

4

4

3

2

1

UNIT  B

Ter

mi

n

al

INDOOR  UNIT

UNIT  A

A

(A)

(B)

(B)

(C)

B

Termi

n

al (

8

P)

OUTDOOR  UNIT

Gro

un

di

ng

 li

n

e

Gro

un

di

ng

 li

n

e

Gro

un

di

ng

 li

n

e

S

i

ng

le-pha

s

e 220-240VAC  50Hz

                        220VAC  60Hz

Power  

su

pply

(B)

(B)

(C)

Fig. 25c

2 indoor units with SAP-CMRV1926

Fig. 25a

08-253 CMRV3146EH_OU EN  10/14/08  2:39 PM  Page 20

Summary of Contents for SAP-CMRV1926EH





























Reviews: