Sanyo SRC-850 Instruction Manual Download

Page: 33 / 35

SPECIFICATIONS

General Specifications

Video heads system

Dual-azimuth 4-head rotating helical scanning system:
  Dual azimuth 2-head for record and standard playback
  Dual azimuth 4-head for forward picture search, reverse picture search
  and still mode

Audio recording

In 8-hour mode

Tape speed

11.12 mm /sec

Specified video cassette tape

VHS 1/2 inch video cassette tape

Recording/playback time

8 hours (when using T-160 tape)

Fast forward/rewind time

approximately 3 minutes 30 seconds (when using T-160 tape)

Television system

NTSC color TV system

RS-485 data transfer speed

19200, 9600, 4800, 2400 baud

Video

Recording method

Luminance signal: FM recording
Chrominance signal: Down-converted direct recording

Video input

1 V(p-p), BNC, 75

Ω

, unbalanced

Video output

1 V(p-p), BNC, 75

Ω

, unbalanced

Horizontal resolution

Black & white mode

350 line or more

Color mode

300 line or more

Audio

Input

–8 dBs, RCA pin jack, 27 k

Ω

, unbalanced

Output

–8 dBs, RCA pin jack, 600

Ω

, unbalanced

Microphone input

–60 dBs, 3.5 mm mini jack, 10 k

Ω

, unbalanced

Connectors

Alarm input

Low level active (0V 100msec or more)

Alarm output

DC 5 V (

0.5)/5.7 k

Ω

, Low at alarm

Switch output

DC 5 V (

0.5)/5.7 k

Ω

, Low at switching

Tape end output

DC 5 V (

0.5)/5.7 k

Ω

, Low at tape end

Warning output

DC 5 V (

0.5)/5.7 k

Ω

, Low at warning

Eject input

Low level active (0V 100msec or more)

Eject output

DC 5 V (

0.5)/5.7 k

Ω

, Low at eject in

Series input

Low level active (0V 100msec or more)

Series output/Non rec output

DC 5 V (

0.5)/5.7 k

Ω

Common

0 V (GND)

RS485 A

Non-inverting driver output/receiver input

RS485 B

Inverting driver output/receiver input

Remote control input

3.5 mm mini jack

Other Specifications

Operating temperature range

5°C to 40°C

Operating humidity range

80% or less

Power requirements

120 V AC, 60 Hz

Power consumption

17 W

Dimensions

240 (W) x 96.5 (H) x 335 (D) mm

Weight

approximately 3.8 kg

NOTE:

The specifications and external appearance of this unit are subject to change without notice.

NU4Q/U3 (SRC-850 GB) Mon. Aug., 23/1999

English

Summary of Contents for SRC-850



































Search results

Summary of Contents for SRC-850

Reviews:

Related manuals for SRC-850

Brands by name

Popular brands

Sanyo SRC-850, Instruction Manual

Search results

Summary of Contents for SRC-850

Reviews:

Related manuals for SRC-850

Brands by name

Popular brands