background image

SYNCHRONIZATION CONTROL

When two or more of this model of VCR are connected
together, the VCRs can be operated simultaneously just
by operating the VCR that has been set to “MASTER”,
without using a system controller (sold separately).

There are two modes available: operator mode and
administrator/installer mode. The operations that can be
carried out in each mode are different.

NOTES:

œ

The operation and setting can only be carried out with
the button of this unit.

œ

Use cables with a thickness of A.W.G.24 (0.2 mm

2

) or

more and a length no more than 1.5 m to connect
VCRs.

œ

It is recommended that you do not connect any more
than 10 VCRs together.

œ

Only one VCR can be specified at the master unit.

œ

Do not mix operator mode and administrator/installer
mode in the same installation.

œ

Do not connect the VCRs in a loop.

œ

“TERMINAL SET” in the (OTHERS) menu should
always be set to “SET1”.

œ

The VCR operation may not be completely
synchronized depending on the VCR statuses, the
operating environment and the operation timing. It is
recommended that you check the operating statuses
and menus after carrying out each operation.

Connection

Operator Mode

This mode lets you carry out basic operations (ejecting,
recording, stopping, rewinding and changing the
recording speed mode).

NOTE:

œ

This mode will not work correctly unless the VCRs are
in the same initial state.

1

Press the MENU button to display the MAIN MENU.

2

Press the 

l

 (or 

j

) button to select the “4.WARNING

OUT/CONTR. SET” line, then press the ENTER
button.

ø

The (WARNING OUT/CONTROL SET) menu
appears.

<WARNING@OUT@SET>SET@UP

ALARM@@@@@@@@@@@@Y

NON@REC@@@@@@@@@@N

MECHA.PROBLEM@@@@Y

<CONTROL@SET>

EJECT@MODE@@@@@@@EJECT1

OPERATION@@@@@@@@SLAVE

3

Press the 

l

 (or 

j

) button until the “OPERATION”

setting is highlighted, then press the ENTER button.

4

Press the 

l

 (or 

j

) button to select the desired

operation, then press the ENTER button.

SLAVE . . . . . . . . . . . . .  The function is restricted

to only the VCR being
operated.

MASTER

. . . . . . . . . .  The function is applied to

the VCR being operated
and all VCRs that are
connected after it.

œ

When the “OPERATION” is set to “MASTER”,

[

” lights on the digital display.

5

Press the MENU EXIT button.

VCR No. 1

VCR No. 2

To CONTROL IN terminal

To COM terminal

CONTROL IN

COM

CONTROL OUT

CONTROL IN

COM

CONTROL OUT

NB4Q/NA, NB4Q/NA2 (TLS-4960/TLS-4072 GB)  Wed. Oct., 30/2002

English

39

Summary of Contents for TLS-4072























































Reviews: