background image

CONNECTIONS

Turn off the power for all components before connecting them.

Be sure to carefully read the Instruction Manual for all equipment being connected to the camera.

If the connections are incorrect, smoke or operating malfunctions may result.

Basic connections (RS485)

EXT TIM

ER IN

SERIES IN

CONTR

OL IN

ALARM

(1 SHO

T) IN

(ALARM RESET

GND

A

B

RS485

TV monitor

(sold separately)

System controller

(sold separately)

To AC 24 V

Power supply cable (AC 24 V, 60 Hz)

Video output connector (BNC)

Camera control
connector (5 pin)

Camera control expansion
connector (5 pin)

Alarm output expansion
connector (5 pin)

Alarm input expansion
connector (10 pin)

Alarm output
connector (5 pin)

Alarm input
connector (10 pin)

Digital video recorder (sold separately)

Connect an external switch

to an ALARM IN connector

 Pin 1 is shown by the arrow

Connecting external alarm sensors

To enable external alarm sensors, connect the supplied alarm input 
expansion connector to the alarm input connector, then connect external 
switches to suitable lead wires of the expansion connector. When an 
intruder triggers the external switch (such as opening and closing a door), 
the alarm signal is received and an alarm sounds. See the alarm setting 
section for details. (See p45)

Buzzer or lamp

(

)

(

)

(

)

English

– 5 –

Summary of Contents for VCC-9400























































Reviews: