Français
English
POWER VIDEO OUT
CLASS 2 WIRING
GND
A
C24V
--
DC12V
--
A
B
b
Supported coaxial cables
Thicker than RG-6U (5C-2V)
Length: 500 m / 547 yds max.
• RG-11U (7C-2V): 600 m / 656 yds max.
If you use a cable other than the type
above, the image or sync signal will be
attenuated and will not be transmitted
correctly.
A
Power cable
(For the connections, use cables thicker than 18 AWG.)
B
Control terminal connection
Under near infrared lighting or other similar conditions, hunting reaction may occur
because the Day/Night function is not carried out normally. In such case, refer to the
following diagram for cable connection to fix the image either to color or black-and-white
by using an external switch, etc.
<AC 24 V connection>
<DC 12 V connection>
To prevent a fire hazard use any
UL listed wire rated VW-1.
Check that polarity is correct.
You cannot control the switchover operation by using an external switch, etc., while switching
between color and black-and-white images is actually in progress by the DAY/NIGHT function.
GND
A
C
24V
--
DC12V
--
AC 24V
GND
A
C
24V
--
DC12V
--
DC 12V
Control terminal
(
●
indicates a connection point.)
COLOR
B/W
COM
B/W
–
●
●
Color
●
–
●
COLOR
B/W
COM
AWG24:
600 m/656 yd
max.
The camera comes pre-adjusted and ready to install at the time of factory shipment, but you can make adjustments or settings if you need.
If you have trouble adjusting the camera, consult your dealer or an Authorized Sanyo Service Center.
b
INT (Internal sync)
b
L-L (Line-Lock)
b
ON
[LEVEL]
The greater the number, the brighter the dark area becomes.
• This setting may cause the noise generation.
[SENSITIVITY]
The greater the number, the stronger the contrast between light and
dark areas becomes.
• This setting may cause the image to obtain unnatural contours.
b
OFF
b
AI (Auto Iris)
b
EI (Electronic Iris)
When using a manual or fixed iris lens and the electronic iris function is
on (For indoor use)
• Set the lens aperture to the shortest F stop.
• If fluorescent lighting is used where the camera is installed, the
object will flicker as a result. This type of phenomenon can be
avoided by replacing the fluorescent lighting with incandescent
lamps.
• If the light entering the lens exceeds the maximum required
illumination, the image cannot be displayed properly. In that case,
manually adjust the lens iris.
• If “WD” is “ON”, “EI” is disabled.
• If “IRIS” is set to “EI”, “SHUTTER” is disabled.
b
ATW (Auto-Tracing White balance)
b
MWB (Manual White Balance)
b
NORMAL
b
HIGH (For a dark subject)
Setting with which a bright image is obtained in a lower illuminance than
the NORMAL setting.
• This setting may cause noise generation and a grainy image.
b
OFF
<VCC-WD8875P>
<VCC-WD8874>
• With the increase in shutter speed number, faster movement can be
captured, though the image becomes darker.
• If “IRIS” is set to “EI”, “SHUTTER” is disabled.
b
AUTO
[LEVEL]
LOW:
Switches in darker conditions.
HIGH:
Switches in brighter conditions.
[BURST] ON/OFF
Burst signal inserted into the Black-and-White image.
b
COLOR
Color image on a steady basis; suitable for always bright location or
conditions.
b
B/W
[BURST] ON/OFF
Burst signal inserted into the Black-and-White image.
• The color image will be displayed first when the power is turned on.
• When switching between color and black-and-white images
automatically, it is normal for movement of the optical filter to be
heard and for a vertical black band to move across the screen.
• Switching from black-and-white to color may occur if there is a
significant degree of reflection from the object when using infrared
illumination in black-and-white image. Adjust the illumination to avoid
switching to color image.
• The focus setting position may differ between color and
black-and-white images. Carry out adjustment to ensure that the
focus for both images is in the optimum position.
1
TITLE (Naming Cameras)
b
OFF
b
ON
Press the
jldc
buttons to select a character, and then press the
SET button.
✱
If you want the name to be displayed on the monitor in two lines,
insert the line feed mark (
) in the “ID string”. You can enter up to 16
characters including the line feed mark (
).
&
To determine thse display position of the name
• On the normal monitoring screen, the name will be displayed.
&
To delete the name specified
Set [PRESET] to “ON”, and press the SET button.
• All the characters will be replaced with “?”.
2
DNR (Digital Noise Reduction)
• The digital noise reduction can be used to reduce the noise
generated when the luminance level is low.
• The greater the number, the lower the noise becomes.
However, this setting may lower the resolution.
SYNC
Sync Setting
Only when using an AC power supply
WD
Wide Dynamic Range
Only when using an auto-iris lens
Correction is made for simultaneous
monitoring of subjects which are different
in brightness, one in a dark room and
another in bright outdoor environment, for
example.
BLC
Backlight Compensation
Only when using an auto-iris lens
b
OFF
b
ON (Center zone metering)
IRIS
Iris Setting
Only when using an AC power supply
L-L SETTING
[V SYNC PHASE]
0
+
Make adjustments so that the vertical
synchronization of the monitor screen
does not move up or down.
WD SETTING
[LEVEL]
8
+
[SENSITIVITY]
3
+
If “IRIS” is set to “EI”, setting “WD” to
“ON” will force the iris setting from “EI” to
“AI”. This setting will remain “AI” after
setting “WD” to “OFF”.
IRIS SETTING
[LEVEL]
50
+
The greater the number, the brighter it
gets.
WHITE BALANCE
White Balance
AGC GAIN
Auto Gain Control
SHUTTER
Shutter Speed
■
Select from:
50, 120, 250, 500, 1000, 2000, 4000, and 10000
(e.g., 50 refers to 1/50 second)
■
Select from:
60, 100, 250, 500, 1000, 2000, 4000, and 10000
(e.g., 60 refers to 1/60 second)
APERTURE
Aperture Compensation
b
NORMAL
b
HIGH
b
LOW
b
OFF
DAY/NIGHT
Day/Night Setting
MWB SETTING
R 112
B 60
+
+
R
: Adjusting Red
B
: Adjusting Blue
The greater the number, the deeper the
tint becomes.
D/N SETTING-AUTO
LEVEL
BURST
LOW
OFF
Automatically switches between COLOR
and B/W mode depending on the
ambient brightness (DAY/NIGHT
function).
D/N SETTING-B/W
BURST
OFF
B/W image on a steady basis; suitable
when sensitivity is prioritized.
OPTION
Option Settings
MEMO:
If you want to overwrite the character, select [ID] using
l
button and move (
) onto it in the ID string using
d
or
c
button, and then select any new character.
■
Select from:
1, 2, OFF
OPTION
TITLE
DNR
OFF
1
:;~ABCDEFGHIJKLM123
,. NOPQRSTUVWXYZ456
+-/abcdefghijklm789
'()nopqrstuvwxyz*0#
POSITION
PRESET
MENU
SET
OFF
BACK
????????????????
y
"<> &!
2
✱
• The characters are
displayed starting from (
)
in the ID string.
• You can enter up to 16
characters.
• The characters “???....” do
not appear on the
monitoring screen, but if you
select “ON” for the [TITLE]
and then enter no character
at all, the monitor will show
you “???....”.
Character Selecting Field
ID String
POSITION
PRESET
MENU
SET
OFF
BACK
ROOM1???????????
y
Select [POSITION] – “SET” and press
the SET button.
ROOM1
Determine the display position of the
name using
jldc
button, and then
press the SET button.
CONNECTIONS AND ADJUSTMENTS
All the power supplied to the system should be turned off when you connect devices.
Monitor
(sold separately)
b
Learning the Menu Setting Operations
1
To reset the menu settings to the
defaults (factory settings), select
“ON”.
2
To return to the previous screen,
select “BACK”.
To close the menu screen, select
“END”.
SYNC
WD
BLC
IRIS
WHITE BALANCE
AGC GAIN
SHUTTER
APERTURE
DAY/NIGHT
OPTION
PRESET
MENU
y
y
y
y
INT
ON
OFF
AI
ATW
NORMAL
60
NORMAL
AUTO
SET
OFF
END
SET
SET
1
2
Menu Item
Next
Screen
<Main Menu>
Press and hold
the button for
about 3 seconds.
Setting Value
PRESET
MENU
ON
END
SET
PRESET
MENU
ON
BACK
SET
L5CU2_XE_US(VCC-WD8875P_WD8874)(GB).fm 2 ページ ２００８年１１月１２日 水曜日 午前１０時１４分
