background image

– 20 –

4. USB STORAGE INFORMATION
    REGISTRATION

USB storage data is important for when the camera is con-
nected to a computer via a USB connection.
If there are any errors in the USB storage data, or if it has not
been saved, the USB specification conditions will not be sat-
isfied, so always check and save the USB storage data.

Preparation:

POWER switch: ON

Adjustment method:

1. Connect the camera to a computer. (Refer to 3-5. Con-

necting the camera to the computer on the page 15.)

2. Double-click on the DscCalDi.exe.
3. Click on the Get button in the USB storage window and

check the USB storage data.
VID: SANYO
PID: C4
Serial:
Rev. : 1.00

4. Check the “Serial” in the above USB storage data. If the

displayed value is different from the serial number printed
on the base of the camera, enter the number on the base
of the camera. Then click the Set button.

5. Next, check VID, PID and Rev. entries in the USB storage

data. If any of them are different from the values in 3. above,
make the changes and then click the corresponding Set
button.

Firmware

Image

AWB

Focus

UV Matrix

RGB Odd

RGB Gain

Tint

RGB Even

VCOMDC

Phase

LCD

Calibration

Upload

Initialize

LCD Type

H AFC

Test

VCOMPP(LOW)

VCOMPP(HI)

Cal Data

Cal Mode

OK

OK

EVF

USB storage

Get

Set

VID

Set

PID

Set

Serial

Set

Rev.

Set

Setting

Language

Video Mode

VCO

Factory Code

Hall Cal.

Summary of Contents for Xacti VPC-C4



































Reviews: