- 65 -
Service Adjustment
Group/Item
Item Name
Function
Initial
Range Note
11 OnStart Cooling Start Threshold
With Onstart on. At the time of
Power on after Cooling imperfect.
Cooling The temperature set point
for existence judgement
38
0-100
12 After shutdown cooling
Cooling after shutdown (0: No, 1: Yes)
1
0-1
Group 256
Fan Lamp Voltage Down Setting
0 Lamp Voltage
Current Lamp Voltage (0.1V)(Read
only)
-
0-255
1 Lamp Vol Threshold
Threshold to judge Lamp Voltage
Down ( V×10)
0
0-0
2 Fan1 Speed Gain
Additional Fan Speed of Min at Lamp
Voltage Down (unit: 0.1V)
10
0-255
3 Fan2 Speed Gain
10
0-255
4 Fan3 Speed Gain
10
0-255
5 Not used
-
Group 257
Fan Dimmer Setting
0 Dimmer Average Check Period
Dimmer Avarage measurement Time
(0:10sec, 1:30sec, 2:60sec, 3: 90sec
...10:300 sec)
1
0-10
1 Dimmer Average
Dimmer Avarage Value (Read only)
-
2 Last Voltage Difference
Read only (Unit : o.1V)
-
3 Voltate Difference Goal
Read only (Unit : o.1V)
Group 258
Fan IC Temp for Netowrk model
0 Standby Cooling Check Cycle
Temp B Check Cycle (Standby
mode) Unit : minute
3
0-100
1 Standby Cooling Start
Threshold
Temp B start threshold (Standby
mode) Unit : minute
44
0-100
2 Standby Cooling Enable
0 : Disable 1 : Enable
1
0-1
Group 260
Auto Calibration (Commn)
0 Execute Calibration
0
0 - 1
Executes Auto-Calibration when
changiing the Value (PC White 100%)
1 Loop Count
Maximum Execution Times (OFFSET-
>GAIN)
10
1 - 30
2 Auto Status
Result of Auto-Calibration (Last
Memory)
0
0 / 1 / 9 0: OK, 1: Adjusting,9: Error * ReadOnly
3 AutoWait
Wait Value for each setting
1
1 - 20
4 CHECK -Tolelance
Torelance of OFFSET
2
1 - 255
Group 261
Auto Calibration (RGB)
0 OFFSET AREA H START
Black Level Acquiring Area H-Start
Position
975
0 - 1000
1 OFFSET AREA V START
Black Level Acquiring Area V-Start
Position
500
0 - 1000
2 GAIN AREA H START
White Level Acquiring Area H-Start
Position
25
0 - 1000
3 GAIN AREA V START
White Level Acquiring Area V-Start
Position
500
0 - 1000
4 Image AREA H WIDTH
Black/White Level Acquiring Area
13
0 - 4095
5 Image AREA V HIGHT
Black/White Level Acquiring Area
Height
9
0 - 4095
6 OFFSET target
Target Value of Black Level Adj.
3
0 - 127
7 OFFSET torelance
Torelance of Black Level Adj.
1
1 - 127
8 GAIN target
Target Value of White Level Adj.
238
0 - 255
9 GAIN torelance
Torelance of White Level Adj.
1
1 - 255
Group 262
Auto Calibration (CVBS/SVIDEO)
0 Y Image Area Start X
Y Acquiring Area H-Start Position
20
0 - 1000
1 Y Image Area Start Y
Y Acquiring Area V-Start Position
200
0 - 1000
6 Image Area H Width
Image Level Acquiring Area
8
0 - 4095
7 Image Area V Hight
Image Level Acquiring Area Height
9
0 - 4095
8 Y Target Level
Target Value of Y Level Adj.
217
0 - 255
11 Gain Tolerance
Torelance of Level Adj.
1
0 - 255
12 Delta Gain
Deviation Width of Gain Value
9
0 - 255
Group 264
Auto Calibration (YCbCr)
0 Y-OFFSET AREA H START
Y - Offset Acquiring Area H-Start
Position
925
0 - 1000
1 Y-OFFSET AREA V START
Y - Offset Acquiring Area V-Start
Position
500
0 - 1000
2 CB - OFFSET AREA H START
CB - Offset Acquiring Area H-Start
Position
925
0 - 1000 If not used: use Y's value
3 CB - OFFSET AREA V START
CB - Offset Acquiring Area V-Start
Position
500
0 - 1000 If not used: use Y's value
Summary of Contents for XGA ULTRA SHORT-THROW PLC-XL51
