Sapido GR-1102 User Manual Download

Page: 272 / 276

http://www.sapido.com.tw

User’s Manual V1.0

272

It is a security risk, since the firewall is disabled.

Only one (1) PC can use this feature.

Q: I can’t connect to the Wireless Router to configure it.

A: Check the following:

The Wireless Router is properly installed, LAN connections are OK, and it is

powered ON.

Make sure that your PC and the Wireless Router are on the same network

segment.

If your PC is set to “Obtain an IP Address automatically” (DHCP client),

restart it.

If your PC uses a Fixed (Static) IP address, make sure that it is using an IP

Address within the range 192.168.1.129 to 192.168.1.253 and thus

compatible with the Wireless Router’s default IP Address of 192.168.1.254.

Also, the Network Mask should be set to 255.255.255.0 to match the

Wireless Router. In Windows, you can check these settings by using Control

Panel ~ Network to check the Properties for the TCP/IP protocol.

Q: The WinXP wireless interface couldn’t communicate the WEP with N+ 3.5G

Mini Server Router wireless interface.

A: The default WEP of WinXP is Authentication Open System - WEP, but the

WEP of N+ 3.5G Mini Server Router is only for Shared Key - WEP, it caused

both sides couldn’t communicate. Please select the WEP of WinXP from

Authentication Open System to Pre-shared Key - WEP, and then the WEP

wireless interface between WinXP and N+ 3.5G Mini Server Router would be

communicated.

9.7

Samba Server

Q: Why can’t I access the Samba Folder via my network places while

connecting to N+ 3.5G Mini Server Router?

A: First, you should check if you have connected assigned storage device properly.

Then enable Samba Server afterwards, so that it can be accessed.

9.8

USB FTP Server

Q: How does N+ 3.5G Mini Server Router assign numbers for the Hard Disk?

Summary of Contents for GR-1102





















































































































































































































































































Search results

Summary of Contents for GR-1102

Reviews:

Related manuals for GR-1102

Brands by name

Popular brands

Sapido GR-1102, User Manual

Search results

Summary of Contents for GR-1102

Reviews:

Related manuals for GR-1102

Brands by name

Popular brands