Sargent and Greenleaf 6128 Programming And Operations Manual Download

Page: 10 / 32

630-600

MODEL 6128/6129 PROGRAMMING & OPERATIONS GUIDE

2.4 — User Access Modes and Opening the Lock

Multiple User —

The lock can be opened by entering any valid code other than the Programming

Code . If time delay is activated, any valid code (except the Programming Code) can be entered to

start the time delay . Then any valid code (except the Programming Code) can be entered during

the opening window to open the lock .

Manager/Employee —

The Group Officers or Administrators enable/disable the access by the

User Codes . When in this mode the Group Officer and Administrator Codes do not open the lock .

To enable your lock in Manager/Employee mode

Enter: Your 2-digit Officer/Administrator PIN position

Your 6-digit Officer/Administrator PIN Code

x x x x

Lock is enabled for use by User PIN positions .

To disable your lock in Manager/Employee mode

Enter: Your 2-digit Officer/Administrator PIN position

Your 6-digit Officer/Administrator PIN Code

x x

Lock is disabled for use by User PIN positions .

Dual Control —

Two valid codes are required to make any programming changes or to open

the lock . These may be either User or Officer/Administrator Codes . The second code must be

entered within 60 seconds after entry of the first code . If time delay is activated, only one code

is required to start the time delay, but both codes must be entered during the opening window to

open the lock .

Time Delay —

The lock may be programmed with a time delay from 0 - 99 minutes with an

opening window of 1minute to 10 minutes .

If your lock does not use the time delay

Enter: Your 2-digit PIN position

Your 6-digit PIN Code

x x x

After the beeps, turn the safe handle to the unlocked position within 6 seconds .

2.3.3 — Additional Actions/Conditions for Service Mode

Action/Condition

Tone & Keypad LED KEB LEDs

Duration

Lockout initiated

3 brap

Red + Amber

1 cycle

Service Mode initiated

Amber

Duration of SM Activity

3 beep

+ 2 beep

Secure condition —
prompt user

Amber + flash
Green

1 cycle - flash
until timeout

Prompt user
for input

1 beep

Amber + flash
Green

1 cycle - flash until
timeout

Lock initialization
successful

1 beep

Green + Amber

1 cycle

Lock initialization
failed

2 brap

Red + Amber

1 cycle

Summary of Contents for 6128

































Search results

Summary of Contents for 6128

Reviews:

Related manuals for 6128

Brands by name

Popular brands

Sargent and Greenleaf 6128, Programming And Operations Manual

Search results

Summary of Contents for 6128

Reviews:

Related manuals for 6128

Brands by name

Popular brands