background image

3

630-600

MODEL 6128/6129 PROGRAMMING & OPERATIONS GUIDE

GENERAL INFORMATION

1

.

6128 /6129 Motorized lock — 

housed within the safe . Provides for 

Bank and Service modes of operation .

Keypad Extension Base — 

Installed 

under the keypad . This is required 

when using the lock’s Service Mode 

operation or audit trail function . The 

extension base provides a green LED 

to indicate “Status 1”, and a red LED to 

indicate “Status 2” and a yellow LED to 

indicate “Mode” of lock operation . The 

extension base also provides a port for 

communication with Touch Keys .

Keypad — 

on front of safe door . This 

is a 12-key alphanumeric keypad used 

to enter PIN codes and programming 

commands .

1.1 — Security Hierarchy

The Model 6128 ATM banking lock system operates in a Bank Mode only, Service Mode 

only, or both Bank and Service Mode simultaneously .

Bank Mode Only 

- Bank users have local control of user PIN positions and codes, and 

programming through the keypad .

Service Mode Only -

 Requires the “Lock Management System” for programming Touch 

Memory Keys and generating one-time use Operation codes for service users . Bank User 

PIN codes are disabled .

Bank and Service Mode - 

Bank users have local control of PIN positions and codes, and 

limited keypad programming commands . The “Lock Management System” controls Bank 

mode optional features and is used for programming Touch Memory Keys and generating 

one-time use codes .

1.2 — About Your Locking System

The Model 6128/6129 Comptronic™ Electronic Lock has the following  

hardware components:

Summary of Contents for 6128

































Reviews: