background image

2

351 STANDARD APPLICATION INSTRUCTIONS

INSTALL DOOR CLOSER TO DOOR WITH
SPRING ADJUSTMENT NUT AWAY FROM HINGE.

NOTE: 351 CLOSER BODIES ARE NON HANDED.
IT IS IMPORTANT THAT THE CLOSER BODY BE
MARKED WITH “RH” SYMBOL AT TOP, FOR RIGHT
HAND DOORS. “LH” SYMBOL AT TOP FOR LEFT
HAND DOORS.

ATTACH ARM WITH INDEX MARK ON SPINDLE ALIGNED AS SHOWN. SECURE WITH SCREW AND
WASHER. INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW AS SHOWN BELOW.

ATTACH FOOT TO FRAME AS SHOWN
WITH NUT UP FOR RH DOOR OR
DOWN FOR LH DOOR.

RIGHT HAND

DOOR SHOWN

DIM. "B"

DIM. "A"

RH

ALTERNATE

STANDARD

9 1/2"

6 1/2"

12 3/4"

9 3/4"

MOUNTING

110

DIM.

B

DIM.

A

MAX. DOOR

OPENING

IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN
OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING

IF BUTT, FRAME AND WALL CONDITIONS PERMIT DOOR WILL
OPEN 180°

160

ARM

TYPE

“H”

HOLDER

ARM

RIGHT HAND DOOR SHOWN. LEFT HAND
DOOR OPPOSITE.

1

2

THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.

C OF HINGE PIVOT:
BUTTS, OFFSET PIVOTS,
SWING CLEAR, CENTER HUNG
OR INVISIBLE HINGES

#12 x 3 WOOD
SCREWS OR
#12-24 X 2 1/4
FLAT HEAD
MACHINE SCREWS

L

1

2

3

4

5

INDEX MARK
ON SPINDLE

MAIN ARM

DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE
NUTS WHEN REQUIRED. SEE PAGE 6 FOR MORTISE NUTS.

9"

2 1/2"

9/16"

1 1/8"

TOP OF DOOR

2 1/2"

RIGHT HAND DOOR

POSITION OF
MAIN ARM WHEN
ASSEMBLING
TO SPINDLE

ROD

ARM
SCREW

HOLD OPEN
ARM

90°

NUT FACES DOWN

LEFT

HAND

DOOR

NUT FACES UP

RIGHT

HAND

DOOR

A

B

C

A7341A

Copyright © 2007, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.

Summary of Contents for POWERGLIDE Series







Reviews: