The most important menu codes
for the weighing mode:
Amb. conditions
Code
Very stable
1 1 1*
Stable
1 1 2*
Unstable
1 1 3
Very unstable
1 1 4
Weighing/filling
Code
Std. weighing
1 2 1*
Filling
1 2 2
Stability Range
When the stability symbol/wt. unit
is displayed, the weight readout
is stable within the defined range.
Code
0.25 digit
1 3 1
0.5 digit
1 3 2*
1 digit***
1 3 3
2 digits***
1 3 4*
4 digits***
1 3 5
8 digits**
1 3 6
Tare parameter
Code
At any time**
1 5 1
After stability
1 5 2*
At stability
1 5 3
Auto Zero
Code
On
1 6 1*
Off
1 6 2
Data Output
Automatic output
of parameters
Code
Off
7 1 1*
Ref. %/qty. + ref. wt.
7 1 2
Ref. weight only
7 1 3
Data ID code
Code
Without
7 2 1*
With
7 2 2
Auto tare output/print
Code
Indiv. tare weight
7 3 1*
Tare weight total
7 3 2
Output parameter
Code
Without stability
6 1 1
After stability
6 1 2*
At stability
6 1 3
Auto w/o stability
6 1 4
Auto after stability
6 1 5
Auto tare after output
Code
Off
6 4 1*
On
6 4 2
Additional Functions
Access to menu
Code
Accessible
8 1 1
Dep. on switch setting** 8 1 2*
Beep tone
Code
On
8 2 1*
Off
8 2 2
*
**
= factory setting; depends on the
balance model in some cases
**
*
= does not apply to balance
models verified
for legal metrology
***= only does not apply to verified
AC balances
The Most Important Menu Code Settings
These charts summarizing the menu parameters for standard weighing have been compiled to provide you with
a quick-reference guide.
Weighing in Three Ranges Max.
One range
Code
2 1 1
Two ranges
Code
2 1 2*
Three ranges
Code
2 1 3**
Weight units
1st range 2nd range 3rd range**
Grams (o)**
1 7 1
3 1 1
3 3 1
Grams
1 7 2* 3 1 2* 3 3 2*
Kilograms***
1 7 3
3 1 3
3 3 3
Carats**
1 7 4
3 1 4
3 3 4
Pounds**
1 7 5
3 1 5
3 3 5
Ounces**
1 7 6
3 1 6
3 3 6
Troy ounces**
1 7 7
3 1 7
3 3 7
Hong Kong taels** 1 7 8
3 1 8
3 3 8
Singapore taels**
1 7 8
3 1 9
3 3 9
Taiwanese taels**
1 7 10 3 1 10 3 3 10
Grains**
1 7 11 3 1 11 3 3 11
Pennyweights**
1 7 12 3 1 12 3 3 12
Milligrams**
1 7 13 3 1 13 3 3 13
Application Programs
Program
Key
Code
Counting
F2 2 1 4
Weighing in percent
F2 2 1 5
Tare memory/net total
F1 2 2 2
Over/under checkweighing (net wt.)
F1 2 2 3
Over/under checkweighing (diff.in wt.) F1 2 2 4
IQ-Mode for Standard Balances
In the IQ-Mode,** weighing is done with a
load-dependent readability. Select the load-dependent
display accuracy independently for each of the three
weighing ranges.
Code
Code
Code
1st range 2nd range 3rd range
1 % accuracy
1 8 6
3 2 6
3 4 6*
0.5 % accuracy
1 8 7
3 2 7
3 4 7
0.2 % accuracy
1 8 8
3 2 8
3 4 8
0.1 % accuracy
1 8 9
3 2 9* 3 4 9
0.05% accuracy
1 8 10 3 2 10 3 4 10
0.02% accuracy
1 8 11 3 2 11 3 4 11
0.01% accuracy
1 8 12 3 2 12 3 4 12
Display Modes
Code
Code
Code
1st range 2nd range 3rd range
Highest accuracy
1 8 1* 3 2 1* 3 4 1
Last num. blanked
when load changes 1 8 2
3 2 2
3 4 2
Rounding factor 2**1 8 3
3 2 3
3 4 3
Rounding factor 5**1 8 4
3 2 4
3 4 4
Rounding factor10**1 8 5
3 2 5
3 4 5
PolyRange**
1 8 13 3 2 13 3 4 13
*
**
= factory setting; depends on the balance model
in some cases
**
*
= does not apply to balance models verified
for legal metrology
***= blocked on verified AC balances
Calibration/Adjustment and
Linearization Functions
External cal.
Code**
Accessible
1 9 1*
Access denied
1 9 2
Internal cal.
Code**
Accessible
1 10 1*
Access denied
1 10 2
Sensitivity test***
Code
Accessible
1 11 1*
Access denied
1 11 2
Quick CAL using
f
Code
Quick CAL (“CAL I”)
2 2 5*
Quick sensitivity test*** 2 2 6
Application Program Functions
Ref. for % + counting
Code
No change
2 3 1
5,10, 20, ...
2 3 2*
In increments of 1
2 3 3
Readout in percent
Code
Without decimal
3 6 1
1 decimal
3 6 2*
2 decimals
3 6 3
3 decimals
3 6 4
Over/under
tolerance limits
Code
+/– 0.1% deviation
4 1 1
+/– 0.2% deviation
4 1 2
+/– 0.5% deviation
4 1 3
+/– 1.0% deviation
4 1 4*
+/– 1.5% deviation
4 1 5
+/– 2.0% deviation
4 1 6
+/– 2.5% deviation
4 1 7
+/– 3.0% deviation
4 1 8
+/– 5.0% deviation
4 1 9
+/– 10.0% deviation
4 1 10
Auto output of
acceptable values
Code
On
4 2 1
Off
4 2 2*
Interface
Baud rate
Code
150 baud
5 1 1
300 baud
5 1 2
600 baud
5 1 3
1,200 baud
5 1 4*
2,400 baud
5 1 5
4,800 baud
5 1 6
9,600 baud
5 1 7
19,200 baud
5 1 8
Parity
Code
Mark parity**
5 2 1
Space parity**
5 2 2
Odd parity
5 2 3*
Even partiy
5 2 4
Number of stop bits
Code
1 stop bit
5 3 1*
2 stop bits
5 3 2
Handshake mode
Code
Software
5 4 1
Hardware w/2
characters after CTS
5 4 2*
Hardware w/1
character after CTS
5 4 3
Reset Function
The reset function enables you to
reset all codes back to the factory
settings identified by an “*” in the
charts. Select code
9 – – 1
o
, confirm
by pressing
t
, then press
c
.
*
**
= factory setting
**
*
= does not apply to balance
models verifiable/verified for
legal metrology
***= does not apply to verified/
verifiable LC balances
