background image

ST-550 zPID

 

 

27

 

 

Statistics 
 

Statistics tab enables the user to view the temperature values for different time periods e.g. 24h, a week 
or a month. It is also possible to view the statistics for the previous months.

 

 

 

VI.9.

 

Fuel level calibration

 

These parameters are used to calibrate the fuel tank. Conducting fuel level calibration properly enables 
the user to view the current level of fuel on the controller screen. Such calibration is usually performed 
only once.

 

The first step involves filling the fuel tank up and selecting the option 

Fuel tank full 

(by pressing 

the pulser knob).

 

The controller

 

remembers the level as full (100%).  

 

When there is no fuel left in the tank, the user should select the option 

Fuel tank empty 

(by pressing the 

pulser knob). In this way the fuel tank is properly calibrated. 

 

Each time the tank is fully filled, a corresponding option should be selected in the menu so that 

the controller will automatically inform the user about the current fuel level.

 

Screenshot presenting an example temperature char

 

Screenshot presenting an example alarm log

 

Summary of Contents for ST-550 zPID





































Reviews: