background image

111

EN

Operating instructions SATAminijet 1000 K/H RP/HVLP

Operating instructions SATAminijet 1000 K/H RP/HVLP

4.  Design of the Spray Gun [1]

[1-1] 

Spray gun handle

[1-2] 

Trigger

[1-3] 

Material connection

[1-4] 

Nozzle set consisting of air 

cap, fluid tip (not visible), 

paint needle (not visible)

[1-5] 

Round/flat spray control

[1-6] 

Material flow control screw

[1-7] 

Material flow control counter 

nut

[1-8] 

Air micrometer

[1-9] 

Air micrometer (air flow con

-

trol) locking screw  

[1-10] 

Air piston (not visible)

[1-11] 

Compressed air connection

[1-12] 

ColorCode-System (CCS)

5.  Intended Use

The spray gun has been designed for the application of paints, lacquers 

and other sprayable media by means of compressed air on suitable sub-

strates and surfaces. 

6.  Safety Instructions
6.1. General Safety Instructions

Warning! Attention!

• 

Before using the spray gun, please read all safety and the operating 

instructions carefully. Safety instructions and indicated safety meas-

ures are mandatory.

• 

Please keep all enclosed documents and make sure that the spray 

gun is handed over only together with these documents.

Summary of Contents for SATAjet 1000 H RP





















Reviews: