background image

20 

Installer Manual 

SATEL 

5.8  Connecting the sirens 

If high-current output is not used, the 2.2 k

 resistor should be connected between the 

output and common terminals. 

 

 

Fig. 9. The way of connecting sirens. I – siren without own power supply – alarm signaling 

triggered by high-current outputs. II - siren with own power supply – alarm signaling triggered 

by low-current outputs, the high-current serving as power supply output. The value of 

resistors R is 2.2 k

. In both cases, tamper circuit is connected to zone Z8. 

 

5.9  Connecting power supply 

Complete all wiring to the control panel before connecting AC power or the 
battery. 

Before connecting power supply, insert the clock and RAM backup battery into 
its socket on the mainboard. 

5.9.1  Main power supply 

The control panel requires 18 V AC (±10%) power supply. Using a transformer of at least 
40 VA power is recommended. 

Do not connect two devices with power supply to one-section transformer. 

Before connecting transformer to a circuit from which it will be powered, make 
sure the circuit is de-energized. 

The transformer should be permanently connected to the 230 V AC mains supply. Before you 
make the cabling, familiarize yourself with the electrical installation of the facility. Make sure 
that the circuit you choose for powering the control panel will be always alive. The power 
supply circuit should be protected with a proper safety device. The owner or user of the alarm 

Summary of Contents for Integra 128-WRL






































Reviews: