SATO KEIRYOKI SK-1260 Instruction Manual Download

Page: 14 / 16

Ⅲ

-3. Examples of the Printed Data

Manual storage mode

Auto storage mode (Recording interval is set to 2 min.)

Rec

Date

Time

Temp

Print-Date : 2016 / 9 / 23

Mes-Code : No. 00-00 (°C)

Measuring Data

Rec

Date

Time

Ave

Max

Min

Print-Date : 2016 / 9 / 23

Sensor : K1, Mes-Code : No. 00-00 (°C)

Measuring Data

Ⅳ

Error Message

• Error massage is displayed on the main 7-segment LCD

Display

Causes

Remedy

Er : Hi

Measured value is higher

than measuring range.

Stop measurement and

bring the value within the

measuring range.

Er : Lo

Measured value is lower

than measuring range.

Measured value exceeds

t h e m e a s u r i n g r a n g e

further.

(appears after Hi

or Lo displayed)

Probe is not connected.

Connect the probe.

Sensor is disconnected.

Poor connection of probe

connector or disconnection

inside the probe.

If disconnection seems to

be the cause, stop using the

thermometer.

Short-circuits inside the

probe.

Stop using the thermometer.

Summary of Contents for SK-1260

















Search results

Summary of Contents for SK-1260

Reviews:

Related manuals for SK-1260

Brands by name

Popular brands

SATO KEIRYOKI SK-1260, Instruction Manual

Search results

Summary of Contents for SK-1260

Reviews:

Related manuals for SK-1260

Brands by name

Popular brands