background image

SETUP 
Setup the griddle only on a firm, level, non-combustible surface.

 

Verify local codes for requirements. Concrete, tile, terrazzo or metal

 

surfaces are recommended. Metal or tile over combustible material

 

may not meet code for non-combustible surfaces. Install the 
provided adjustable legs, one on each corner of the appliance, 
in the holes provided. 

Verify that the unit sits firmly ON ALL FOUR LEGS. 
With the adjustable legs, adjust as required to level the appliance.

 

All  four  legs must  be adjusted  to  firmly  contact  the countertop  in

 

order to prevent tipping. 

Adequate clearance for air openings in the cabinet must be provided.

 

Refer to the Installation Instruction Sheet for required clearances.

 

Maintain required clearances between the appliance and adjacent

 

combustible surfaces. 

The griddle must be installed 
in an area with sufficient 
make-up air for proper 
combustion, and must be 
installed such that the flow 
of combustion and ventilation 
air will not be obstructed. 

 

 

When used with an exhaust fan, special precautions must be

 

observed to avoid interference with the operation of the griddle, such

 

as drafts and air starvation. 

IN

ST

A

LL

A

T

ION A

N

D

 IN

S

PEC
TION

 

Page 5

Carefully remove the appliance from the carton. Remove all

 

protective plastic film, packing materials and accessories from the

 

appliance before connecting performing any installation procedure.

 

Carefully read all instructions in this manual and the Installation

 

Instruction Sheet packed with the appliance before starting any

 

installation. 
Read and understand all labels and diagrams attached to the

 

appliance. 
Carefully account for all components and accessories before

 

discarding packing materials. Store all accessories in a convenient

 

place for later use. 
COMPONENTS 

Adjustable Legs (set of 4)

 

Grease Tray 

NOTE: DO NOT discard 
the carton or other packing

 

materials until you have

 

inspected the appliance for

 

hidden damage and tested it

 

for proper operation. 
Refer to SHIPPING DAMAGE

 

CLAIM PROCEDURE on the

 

inside front cover of this

 

manual. 

DANGER: 
HEALTH HAZARD 
This appliance must be

 

properly ventilated. Failure to

 

provide and maintain proper

 

ventilation of exhaust gasses

 

can result in severe injury or

 

death. 

WARNING: 
FIRE HAZARD 
Do not store gasoline or 
any other flammable or

 

combustible material near this

 

appliance. The open flame 
can cause such materials to

 

ignite. 
The area where the griddle is

 

installed must be kept clear of

 

combustibles and flammables.

 

This includes mops, rags,

 

grease, wrapping paper and

 

electric cords. 

NOTICE: Manufacturer

s

 

warranty on this griddle is in

 

effect only when the griddle

 

is installed in accordance with

 

these instructions and local

 

codes and ordinances or, in

 

the absence of local codes,

 

the National Fuel Gas Code,

 

ANSI Z223.1 (current edition).

 

The manufacturer of this

 

griddle assumes no liability

 

for any damage or injury

 

resulting from failure to

 

comply with this notice. 

Summary of Contents for ESG-15
















Reviews: