background image

INSTALLATION

UNPACKING & INSPECTION

Carefully remove the appliance from the carton. Remove all

protective plastic film, packing materials and accessories from the

appliance before connecting performing any installation procedure.

Carefully read all instructions in this manual and the Installation

Instruction Sheet packed with the appliance before starting any

installation.

Read and understand all labels and diagrams attached to the

appliance.

Carefully account for all components and accessories before

discarding packing materials. Store all accessories in a convenient

place for later use.

IN

ST

A

LL

AT

IO

N

 A

N

D

 IN

SP

EC

TIO

N

COMPONENTS

Dual Burner (

T

SG48-HD, 4 ea.)

Adjustable Legs (set of 4)

Grease Tray (

T

SG48-HD, 2 ea.)

Setup the griddle only on a firm, level, non-combustible surface.

Verify local codes for requirements. Concrete, tile, terrazzo or metal

surfaces are recommended. Metal or tile over combustible material

may not meet code for non-combustible surfaces. Install the  

provided adjustable legs, one on each corner of the appliance, 

in the holes provided.

Verify that the unit sits firmly ON ALL FOUR LEGS. 

With the adjustable legs, adjust as required to level the appliance.

All four legs must be adjusted to firmly contact the countertop in

order to prevent tipping.

Adequate clearance for air openings in the cabinet must be provided.

Refer to the Installation Instruction Sheet for required clearances.

Maintain required clearances between the appliance and adjacent

combustible surfaces.

The griddle must be installed 

in an area with sufficient  

make-up air for proper  

combustion, and must be 

installed such that the flow 

of combustion and ventilation 

air will not be obstructed.

When used with an exhaust fan, special precautions must be

observed to avoid interference with the operation of the griddle, such

as drafts and air starvation.

SETUP

NOTE: DO NOT discard

the carton or other packing

materials until you have

inspected the appliance for

hidden damage and tested it

for proper operation.

Refer to SHIPPING DAMAGE

CLAIM PROCEDURE on the

inside front cover of this

manual.

DANGER:

HEALTH HAZARD

This appliance must be

properly ventilated. Failure to

provide and maintain proper

ventilation of exhaust gasses

can result in severe injury or

death.

WARNING:

FIRE HAZARD

Do not store gasoline or

any other flammable or

combustible material near this

appliance. The open flame

can cause such materials to

ignite.

The area where the griddle is

installed must be kept clear of

combustibles and flammables.

This includes mops, rags,

grease, wrapping paper and

electric cords.

NOTICE: Manufacturer’s

warranty on this griddle is in

effect only when the griddle

is installed in accordance with

these instructions and local

codes and ordinances or, in

the absence of local codes,

the National Fuel Gas Code,

ANSI Z223.1 (current edition).

The manufacturer of this

griddle assumes no liability

for any damage or injury

resulting from failure to

comply with this notice.

Page 5

Summary of Contents for TSG48-HD


















Reviews: