DE
7 BETRIEB
Einschalten des Magneten mit gesenkter magnetischer Leistung
■
Nach dem Einstellen des erforderlichen Wertes der magnetischen Leistung die Funktion
VARIABLE FORCE
durch gleichzeitige Betätigung der
LIFT
und
RELEASE
Tasten an der Fernbedienung aktivieren.
HINWEIS!
Der Lasthebemagnet wird mit eingestellter gesenkter magnetischer Leistung
aktiviert. Gleichzeitig ertönt ein akustisches Warnsignal, das das Bedie-
nungspersonal und die Umgebung auf die durchgeführte Funktion aufmerk-
sam macht, bei der besondere Vorsicht geboten ist. Am Anzeigepanel des
Lasthebemagneten zeigt die gelbe blinkende Kontrollleuchte die gewählte
Funktion an und die rote Kontrollleuchte
DANGER
blinkt.
Die Last vor dem Wiederholen dieser Betriebsart ablegen, Magnetisierung
ausschalten und danach die
VARIABLE FORCE
Funktion erneut aktivieren.
7.3.2
TIP-OFF Funktion
Funktionsbeschreibung
Die
TIP-OFF
Funktion ermöglicht, die magnetische Leistung des Lasthebemagneten bei angezogener Last vorüber-
gehend schrittweise zu senken. Die Leistungsreduzierung erfolgt nach einer zeitdefinierten Kurve, bis die magne-
tische Leistung zum Nullwert sinkt. Nach der Deaktivierung erfolgt eine automatische Leistungserhöhung bis zur
vollen 100% Magnetleistung – somit wird die sichere Handhabung gewährleistet. Während der aktiven
TIP-OFF
Funktion wird das Bedienungspersonal auf den Zustand mit einem akustischen und visuellen Warnsignal aufmerk-
sam gemacht.
Verwendungsbeispiel
■
Ablegen/Freisetzen eines oder mehrerer dünnen Stahlbleche vom gehandhabten Paket.
Sicherheitsmaßnahmen vor der Verwendung der TIP-OFF Funktion
GEFAHR!
Gefahr durch Herunterfallen der Last!
Lebensgefahr durch schwebende Lasten!
Die
TIP-OFF
Funktion kann nur bei aktiver Magnetisierung aktiviert werden.
Bei der Wahl dieser Funktion besteht erhöhte Unfallgefahr! Herunterfallende
Teile (z.B. durch fehlerhafte Bedienung) können schwerste Verletzungen bis
hin zum Tod verursachen.
■
Maximal erhöhte Vorsicht walten lassen!
■
Die zu handhabende Last darf von der Ablagefläche nicht höher als 20 cm entfernt sein.
■
Die Ablagefläche muss fest und waagerecht sein, damit die abgelegte Last nicht rutschen oder stürzen kann.
■
Überprüfen, ob zwischen der Last und der Ablagefläche kein Hindernis liegt (wie etwa Körperteile oder Gegen-
stände).
■
Beachten Sie, dass ein ferromagnetisches Material vom Magnetfeld spontan angezogen werden kann.
Aktivieren der TIP-OFF Funktion
■
Die
TIP-OFF
Funktion wird durch gleichzeitige Dauerbetätigung der
LIFT
und
RELEASE
Tasten auf der Fernbe-
dienung aktiviert.
SAV 531.42
Version 1.0
[
45
]
Summary of Contents for SAV 531.42
