Savant Metropolitan WIS 102 Series, Quick Reference Manual

The Savant WIS-SWS102 (snow white) and WIS-LAS102 (light almond) wireless switches are designed to function within the Savant 
Control system to switch most lighting loads. This includes incandescents, magnetic and electronic low voltage, CFL, and LED. 
The Savant Metropolitan wireless switches replace any standard 120V AC light switch or dimmer. With the addition of the Savant WI3-
xxx102 Auxiliary Control, these switches are compatible with most 3-way wiring designs for multi-location control.
Finally, the WIS-xxx102 communicates with most 802.11 b/g/n wireless networks which allow it to be added to the Savant Control 
system for complete control of all lighting requirements over the local wireless network.

Box Contents

•

Metropolitan Switch without faceplate

•

(2) Mounting Screws 6/32 x 

¾

 inch

•

(5) Wire Nuts

•

Quick Reference Guide (this document)

Optional Accessories

•

1 to 4-gang faceplates

•

Black conversion kits

Specifications

Environmental

Environmental

Temperature

32° to 104° F  (0° to 40° C)

Humidity

10% to 90% Relative Humidity (non-condensing)

Location

Indoor Use Only

Dimensions

Dimensions

Height

4.13 in (10.49 cm) / Shipping 7.0 in (17.78 cm)

Width

2.38 in (6.05 cm) / Shipping 4.5 in (11.43 cm)

Depth

1.81 in (4.60 cm) / Shipping 3.0 in (7.62 cm)

Weight (Shipping)

0.60 lb (0.272 kg)

Recommended Back Box Depth Dimensions

Recommended Back Box Depth Dimensions

All Metro switches require a standard U.S. electrical back box  
• Recommended - 3.5 in (8.89 cm) deep
• Minimum - 2.25 in (5.72 cm) deep

All Metro switches require a standard U.S. electrical back box  
• Recommended - 3.5 in (8.89 cm) deep
• Minimum - 2.25 in (5.72 cm) deep

Power

Power

Input

120V AC at 60 Hz 

Load Power (Max)

600W 5A @ 120V AC

Supported Load Types

Supported Load Types

Standard Configuration

Incandescent, Magnetic/Electronic Low Voltage, CFL, LED

No Neutral Configuration

Not Supported

Standards

Standards

Wireless

802.11 b/g/n

Security

WPA™, WPA2™, WPA1™ + WPA2™, WEP

Regulatory

Regulatory

Safety and Emissions

FCC Part 15  |  UL 
For more details, refer to the 

Regulatory

 section

Contains FCC ID:

TLZ-CU277

Contains IC:

6100A-CU277

RoHS

Compliant

Minimum Supported Release

Minimum Supported Release

Savant® OS

da Vinci® 7.2

Front View

A

Ambient Light Sensor

 - Senses the level of ambient light in the room and adjusts the LED brightness on the front 

panel. The ambient light sensor operation can be modified using RacePoint Blueprint®.

B

Reset Button

 - The reset button has two functions:

• Press and release the reset button. After button is released, all LEDs on the front panel illuminate for two-

seconds and then flash twice. Pressing the reset button causes the switch to calibrate itself to the circuit it is 
being installed to. After the switch calibrates itself, it then reboots. After the reboot, the LED sequencing that 
is now displayed on the main button is determined by whether the device had previously been connected to a 
network. Refer to 

LED Sequencing

 table.

Note:

 The reset button should always be pressed after the Metropolitan device is installed.

• Press and hold the reset button for five seconds until all LEDs on the front panel illuminate. The LEDs remain 

on for two seconds and then flash twice. The switch then reboots and reverts to Provisioning Mode. In 
Provisioning Mode, the LEDs on the main button flash in an alternating pattern waiting for the switch to be 
provisioned. Refer to 

LED Sequencing

 table.

C

Switch LED

 - 

LED lights when button is pressed. LEDs are also used to indicate the state of the switch when 

connecting to a network. Refer to 

LED Sequencing

 table. Once configured in Blueprint, the switch LED shows 

the scene state.

D

Service Switch

 - The service switch removes power from the load (red wire). Toggle the service switch to O

ff

whenever changing the load. The service switch can also be used to power cycle the switch.

Rear View

Device wires are all a five inch #16 AWG stranded wire.

Green

Ground

 - Wire to Gnd.

White

Neutral

 - Return path for voltage.

Yellow

Traveler

 - Wire to the Auxiliary Controller for multi-location control.

Red

Load

 - Wire to the load. 

Black

Line

 - Wire to hot wire from AC power source.

Metropolitan Wireless Switch  |  009-1337-01  |  150522

45 Perseverance Way, Hyannis, MA 02601

Copyright © 2015 Savant Systems, LLC

1

of

2

Savant.com

    |  508.683.2500

Metropolitan Wireless Switch - WIS-xxx102
Quick Reference Guide

For Product Info