Power LED
Green:
System has power and is operating normally.
Red:
System is in standby mode and most of the
controller circuitry is powered down.
Off:
System is not receiving power.
Status LED
Green Blinking:
Embedded system is ready, but no
communication has been established with the host.
Green:
Host has established communications with the
embedded system.
Red Blinking:
Embedded firmware is running, but has
not received a DHCP IP Address.
Red:
Host has determined the firmware needs to be
updated, but a problem occurred during the process
that will initiate a reset.
Amber Blinking:
Embedded system has a valid
link-local IP Address and is connecting to the host.
Amber:
Host is updating the embedded firmware.
Off:
Embedded processor is resetting, or is powered
up, and is booting the embedded firmware.
Hardware Failure:
If a hardware failure occurs, the
status LED indication will be interrupted every three
seconds with a solid red indication. For example, if the
LED is blinking green when a hardware failure occurs,
the LED will alternate between blinking green and
solid red at three-second intervals.
RS232 LED
Green:
RS-232 serial port activity.
Off:
No RS-232 serial port activity.
IR LED
Green:
IR port signal activity.
Off:
No IR port activity.
On/Off Button
On:
Fully enables all internal power rails and processor.
Off:
Disables most internal power rails and processor,
but not internal AC/DC power supply.
Hold On/Off button for about 5 seconds to place
into standby mode. The Power LED turns red. Hold
On/Off button for about 1 second to take system out
of standby mode. The I/O power switch on the back
of unit must be On (I) to enable this function. To turn
the power off for the entire system, press the I/O
power switch on the rear panel to Off [O].
Reset Button
Resets the network.
Hold Reset Button for 5 seconds while powered On
to clear network settings. Status LED will rapidly blink
red when reset is complete.
Zone Protection Red:
Protection mode has been enabled to protect
a zone/channel; typically indicates thermal protection,
clipping or over current.
Off:
Protection mode has not been enabled.
ENCLOSURE INSTALLATION
The Savant Pro Audio 4 device can be mounted to a Structured Media
Enclosure. The Enclosure Brackets need to be attached prior to mounting.
For proper ventilation, louvered enclosure doors are recommended. See
Pro
Audio 4 Deployment Guide
for more information.
A
B
E
C
D
F
G
FRONT PANEL
SAVANT PRO AUDIO 4
QUICK REFERENCE GUIDE
BOX CONTENTS – SKU: SMA-5000
(1) Savant Pro Audio 4 (model: SPA-5000-xx)
(2) Enclosure Bracket (071-1103-xx)
(1) 2U Rack Bracket (071-1102-xx)
(1) Power Cord (064-0079-xx)
(4) #10x½ Screw (039-0405-xx)
(4) Push Rivet (039-0406-xx)
(6) M4 Screw (039-0403-xx)
(4) 4-pin Speaker Connector (028-0702-xx)
(2) 4-pin IR Connector (028-0703-xx)
(4) Rubber Feet (074-0655-xx)
(4) M3 Feet Screw (039-0407-xx)
(1) Quick Reference Guide (this document)
SPECIFICATIONS
ENVIRONMENTS
Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 80% (non-condensing)
Maximum BTU
750 BTU / HR
DIMENSIONS
Height
Width
Depth
Weight
Unit
3.03 in
(7.7 cm)
12 in
(30.5 cm)
14.17 in
(36.0 cm)
10.6 lb
(4.81 kg)
Packaging with
contents
8.27 in
(21.0 cm)
15.55 in
(39.5 cm)
19.41 in
(49.3 cm)
15.1 lb
(6.85 kg)
Rack Space
2U
POWER
Input Power
100/240V AC (50/60 Hz) 2.7A
Maximum Power
225W
OPERATING PARAMETERS
Rated Power
(Speaker Output)
50 WPC at 8 ohms (THD+N < 0.1%)
70 WPC at 8 ohms (THD+N < 1.0%)
Frequency
Response
20 Hz – 20 kHz +/- 0.5 dB, speaker output
Signal-to-Noise
Ratio (SNR)
>95 dB, speaker output
Supported Digital
Input Formats
44.1 kHz / 48 kHz / 96 kHz at 16-bit / 20-bit /
24-bit resolution
NETWORKING
Supported
Standard
IEEE 802.1 AVB/TSN switches
IEEE 802.3 Ethernet
REGULATORY
Safety & Emissions
FCC Part 15B
CE Mark
C-Tick
UL
RoHS
Compliant
MINIMUM SUPPORTED REQUIREMENTS
Release
Savant OS: da Vinci 8.2
Hardware
Requires pairing with a Savant Smart Host or Pro Host.
MUSIC STREAMING
The Pro Audio 4 has a built-in single stream of Savant Music, which includes
popular music streaming services powered by Autonomic MirageOS.
(Streaming service fees may apply.)
RACK INSTALLATION
The Savant Pro Audio 4 device can be mounted in a 2U rack style enclosure
and is compatible with all standard 19-inch National Electrical Manufacturers
Association (NEMA) rack mounts. The 2U Rack Bracket needs to be attached
prior to mounting. See
Pro Audio 4 Deployment Guide
for more information.
C
D
E F
G
A
B
