SHA-B7CRxx-00 | 009-1651-00 | 180424
Copyright 2018 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
| 508.683.2500
2 of 2
3. Grab the shade mount from the SHA-B7CLxx shade mount kit.
4. Like with the shade mount from step 2 above, slide the slot in the shade
mount up into the angled bracket already installed. When seated, the two
mounts will form a 90° angle. See diagram to the right.
Angled Bracket
Tube End Plug
(Idler Side)
Tube End Plug
(Idler Side)
Top View of Angled
Bracket with Corner
Shade Mounts Installed
Install Mounts
Use instructions below to mount the shade corner mount assembly created in steps 1-4 above.
1. Mark on the ceiling where the hanger bolt will be mounted. Ensure the center point of the mount is at least 1
¾
inch from any obstructions.
Savant recommends using a laser level or similar technique to ensure the mount is installed in line with the opposite end motor type shade
mount. As stated earlier in this document, the motor type shade mount should be installed before installing the idler side.
TIP!
The tip below can be used to make the process of marking the wall easier.
a. Mark on ceiling the location for one of the mounts. Refer to the
diagram above.
b. Screw the mounting sleeve onto the hanger bolt until it hits the set screw in the 1 inch sleeve.
c. Using a
3/32
inch hex key, turn the hex head set screw that is screwed into the 1 inch mounting sleeve so the set screw is not
protruding from either side of the sleeve. The shade mount sleeve should now easily slide in and out of the hole in the rear of the
shade mount.
d. Slide the hanger bolt/sleeve assembly into hole on top of one of the shade mounts. Repeat steps a, b, and c and slide a second
hanger bolt assembly into hole in second shade mount of the shade mount corner assembly.
e. Using the initial mark from step a, line the tip of one of the hanger bolts with the mark. Position the corner bracket appropriately
and apply pressure to make indentations in the ceiling of where to install the hanger bolts.
2. Remove the hanger bolt assemblies from the shade mounts. Unscrew the hanger bolt from the 1 inch sleeve. Set 1 inch sleeves aside.
3. Prepare the ceiling where the hanger bolts will be installed and install hanger bolts. Leave
½
inch of machine thread exposed.
HELPFUL:
Savant recommends using a hanger bolt installation tool (8-32 thread) to thread the hanger bolt into the wall. DO NOT use the
provided sleeve to drive hanger bolts into wall as damage to the sleeve will occur.
4. If not already completed from step c above, using a
3/32
inch hex key, turn the hex head set screw that is screwed into the 1 inch mounting
sleeve so the set screw is not protruding from either side of the sleeve. At this point, the shade mount sleeve should easily slide in and out
of the hole in the rear of the shade mount.
5. Screw the mounting sleeve onto the installed hanger bolt until the hex
head set screw in the sleeve is positioned slightly offset from the hole in
the shade mount (see diagram to right). Leaving the set screw offset a
bit will allow the shade mount to be pulled tight to the wall in the next
step.
6. Repeat step 5 for the second hanger bolt/sleeve assembly.
7. Slide the holes in the shade mounts from the corner assembly over the
sleeves until the set screws are visible through hole on side of each
mount. With
³/32
inch hex key, turn the set screw counterclockwise to
back off the set screw a bit until it rests within the hole on the side of
the mount. This will pull the mount tight against the ceiling. See dia-
gram to right.
Leave the
set screw offset
from hole in
shade mount
1 Inch Sleeve
8. Verify shade mounts are tight to the ceiling. If not, turn in the set screw, remove the shade mounts, and adjust the mounting sleeves to en-
sure the mount is pulled tight to the wall or ceiling.
