This digital video module (VOM-VP01F) is used in the Savant family of modular matrix
switchers and controllers including the SSP-XXXX platforms. It enables Savant’s
TrueCommand™ (On-Screen Display) technology.
Box Contents
(1) VOM-VP01F with (1) Fiber Protective Cap
(1) HDMI locking cable (CBL-3LHDMI-xx)
(1) Mini DisplayPort to HDMI cable (064-0222-xx)
(1) Quick Reference Guide (this document)
Accessories
(1) HDMI™ over Fiber Receiver (HRX-F001)
(1) Fiber Receiver and Room Controller (FRC-P100)
Specifications
Environmental
Environmental
Refer to the SSP-XXXX chassis specifications.
If applicable, refer to the SSP-1200E, SSP-2400 or SSP-3600 chassis specification
Refer to the SSP-XXXX chassis specifications.
If applicable, refer to the SSP-1200E, SSP-2400 or SSP-3600 chassis specification
Power
Power
Power supplied from the SSP-XXXX chassis.
If applicable, refer to the SSP-1200E, SSP-2400 or SSP-3600 chassis specification
Power supplied from the SSP-XXXX chassis.
If applicable, refer to the SSP-1200E, SSP-2400 or SSP-3600 chassis specification
Compliance
Compliance
Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
RoHS
Compliant
Grounding Procedure
To avoid damage from electrostatic discharge (ESD) when handling modules, use a grounding
strap as shown below:
Observe the following precautions to prevent ESD discharge damage:
1.
Use an approved ESD wrist grounding strap or an approved wrist or ankle strap. Ensure
the grounding strap makes good skin contact.
2.
Before installing or removing a Savant module, connect the clip end of the ground strap
to the threaded grounding stud on the chassis.
If you plan to return a replaced module to Savant Systems LLC, while wearing the grounded
strap, place the module in the clamshell package that it was originally shipped in or a static
shielding bag to avoid ESD damage to the card.
NOTE
: The wrist strap only protects the component from ESD voltages on the body; ESD
voltages on clothing can still cause damage.
Interconnecting Information
After unpacking and installing the module, interconnect the units by referring to the tables and
procedure below.
Front Panel Connectors
Front Panel Connectors
Fiber Output
Fiber output connections to HRX-F001.
Uses SC-terminated OM3 fiber cable 1000 feet (300 meter)
maximum distance.
Graphics Input
HDMI input video connections from the SVR-4100/4100S.
NOTE
: The Savant fiber solutions use a single strand of OM3 fiber optic cable per connection.
Savant recommends that at minimum two fiber strands are run and available for redundancy
and expansion.
Fiber Optic Best Practices
Warning:
Do not look directly into a fiber optic transceiver or into the ends of fiber optic cables.
Fiber optic transceivers and fiber optic cables connected to transceivers emit laser light that
can damage your eyes.
Warning:
Do not stare into the laser beam or view it directly with optical instruments even if
the interface has been disabled.
Caution:
Do not bend fiber optic cables beyond their maximum bend radius. Bending the
cables beyond their maximum bend radius can damage the cables and cause problems that
are difficult to diagnose.
Caution:
Do not let fiber optic cables hang free from the connector. Do not allow fastened
loops of cables to dangle, which stress the cables at the fastening point.
Fiber Optic Protective Caps
Before plugging a fiber cable into the port on the VOM-VP01F module, you must remove the
protective caps, shown in the next image.
Note
: Always keep the protective caps on unplugged fiber connections.
Audio/Video Modules Installation and Removal
This section provides information about installing and removing a VOM-VP01F.
Equipment/Tools Required
The following items are not supplied and are needed to complete the installation:
•
Phillips screwdriver
•
Module removal tool
Module Installation and Removal
To remove and install audio and video modules from the rear of the Controller, perform the
procedures below.
Caution
:
Before removing or installing any of the modules, remove power from the
SSP-XXXX chassis by setting the power switch to Off (O) and removing the AC power cord.
Failure to do so will result in damage to the equipment.
Installation
Note
: Only install into output slots on chassis.
1.
At the rear of the chassis set the power switch to Off (O) and remove the AC power
cord.
2.
Align the module edges with the grooves near the bottom of the SSP-XXXX chassis
opening.
3.
Slide the module in and push the lower edge of the faceplate until the panel bottoms out
against the rear face of the chassis.
4.
Fasten the module to the chassis frame using the two Phillips retaining screws inserted
through the two outer holes.
Removal
1.
At the rear of the chassis set the power switch to Off (O) and remove the AC power
cord.
2.
Remove the two outer retaining screws.
Retaining
Screw
Retaining
Screw
Slot for
Removal Tool
3.
Insert card removal tool into the rectangular slot in the center of the module.
4.
Lift up to ensure the tool is hooked behind the faceplate and pull the module gently
towards you.
Note
: The Card Removal Tool comes with the chassis.
Video Output Module
(VOM-VP01F)
Quick Reference Guide
009-0487-01
VOM-VP01F
