Savari StreetWAVE SW-1000 Installation Manual Download

Page: 16 / 16

APPENDIX A

Product Specifications

The following is the

product specification sheet for the StreetWAVE™ roadside Unit:

Component

Description

Processor

800 MHz Dual Core iMX6

Memory

4 GB DDR DRAM

Storage

8 GB Flash

HSM

IFX SLI97 for secure storage and signing

DSRC Radios

Two (2), high-power, IEEE 802.11p compliant radios

DSRC Antennas*

6 dBi 5.9 GHz Omni Directional w/ N-type Male connector

Ethernet

One (1) 10/100 (RJ-45) ports

Power Supply

IEEE 802.3at

LED

•

Multi-Color LEDs

•

For Power and Operational Status

•

Compliant to US-DOT v4.1 Specification

Weight

3.5 lbs

Temperature

-35C to +75C

Dimensions

220 mm x 220 mm x 95 mm

GPS*

CEP, 50%, 24 hours static

– 2.0m with SBAS, 2.5m

without assistance.

Standards Compliance

IEEE 802.11p, IEEE 1609.X, FIPS 140-2, US-DOT v4.1

RSU Specification.

Security

1609.2, MAC, and SSL

Enclosure

IP66 rating, pole mount.

* If Supplied by Savari

Summary of Contents for StreetWAVE SW-1000

















Search results

Summary of Contents for StreetWAVE SW-1000

Reviews:

Related manuals for StreetWAVE SW-1000

Brands by name

Popular brands

Savari StreetWAVE SW-1000, Installation Manual

Search results

Summary of Contents for StreetWAVE SW-1000

Reviews:

Related manuals for StreetWAVE SW-1000

Brands by name

Popular brands