background image

6

Step 3.

 (Figure 12) Receiver  to  House 

Supply Wires  Electrical  Connections:  
Connect  the black (hot) wire from the 
ceiling to the black wire   marked   "AC in L"  
f r o m  t h e  r e c e i v e r .  C o n n e c t  t h e 
white(neutral) wire from the ceiling to the 
white wire marked "AC in N" from the 
Receiver. Secure the wire connections with 
the plastic wire nuts provided.

Step 4.

 (Figure 12) If your outlet box has  a 

ground wire (green or bare copper) 
connect it to the fan ground  wires; 
otherwise connect the hanging bracket 
ground wire to the mounting bracket. 
Secure the wire connection  with a plastic 
nut provided. After connecting  the  wires, 
spread them  apart so that the green and 
white wires are on one side of the outlet 
box and black and blue wires are on   the  
other side. Carefully tuck the wire 
connections up into the outlet box.

Note:

 Fan must be installed at a maximum 

distance of 30 feet from the transmitting 
unit for proper signal transmission 
between the transmitting unit and the 
fan's receiving unit.  

8. FINISHING THE 

INSTALLATION

Step 1.

 Tuck connections neatly into 

ceiling outlet box.

Step 2.

 Slide the canopy up to hanger 

bracket and place the key hole on the 
canopy over the screw on the hanger 
bracket, turn canopy until it locks in place 
at the narrow section of the key holes.

Step 3.

 Align the circular hole on canopy 

with the remaining hole on the hanger 
bracket, secure by tightening the two set 
screws.

Note:

 Adjust the canopy screws as 

necessary until the canopy and canopy 
cover are snug. (Fig. 13)

Warning:

 Make sure tab at bottom of 

hanger bracket is properly seated in 
groove of hanger ball before attaching 
canopy to bracket. Failure to properly seat 
tab in groove could cause damage to 
electrical wiring.

Figure 12

Figure 13

White (neutral)

White (neutral)

Green or bare

copper (ground)

White ("AC IN N")

White ("to motor  N")

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire 

exists.)

Outlet box

Black (hot)

Black ("AC IN L")

Black ("to motor  L")

Receiver

Blue (for  light)

Blue (for  light)

Black (motor)

Outlet box

Hanger
bracket

Canopy

Canopy cover

Screws

Summary of Contents for ACROPOLIS












Reviews: