Sawn Craft Micro F-22 Assembly And Setup Manual Download

Page: 2 / 18

Thank you from Sawn Craft.

Thank you for purchasing the Sawn Craft Micro F-22 aircraft. Like the full-scale USAF F-22, in your hands

is a remarkably versatile airplane designed to deliver a pleasure cruiser with an incredible look. The

lightweight and rigid EPS and carbon construction makes it possible for you to experience a wide

performance envelope. This means that no matter how you like to ﬂy, you’ll enjoy both stability and

maneuverability without any sacrifice in precision or control feel.

Your Sawn Craft Micro F-22 aircraft represents the benchmark of ultra-micro performance and aerobatic

versatility. All you have to do next is read and apply the information presented in this instruction

manual.

We sincerely hope that you enjoy your model as much as we do! If you have any troubles with these

instructions or in the setup of your model feel free to contact us and we will provide you with the

service you expect from a hobbyist-owned and operated business.

Jonathan Sawn

Owner, Sawn Craft

Jonathan@Sawn-Craft.com

Summary of Contents for Micro F-22



















Search results

Summary of Contents for Micro F-22

Reviews:

Related manuals for Micro F-22

Brands by name

Popular brands

Sawn Craft Micro F-22, Assembly And Setup Manual

Search results

Summary of Contents for Micro F-22

Reviews:

Related manuals for Micro F-22

Brands by name

Popular brands