background image

14

Steam Generator Parts

NOTE:  

For illustrative purposes only.

Some components may be omitted or altered for clarity.
Do not use for wiring, repair or other purposes not related
to component identification. 

Relay

Contactor

Board

Transformer

Water level probe

Solenoid Valve

Steam Outlet

Neutral

Earth

L1

L2

L3

Diagram 1

Installing the Remote Temperature Probe

for SAWO Controls

Diagram 2

DRAWING NOT 
TO SCALE

SAWO Steam Generator
(shown with cover removed and NOT installed)

Temperature
Sensing Probe

Knock-out

Temperature

Probe Cable

(9 meters)

Temperature Probe
Connection

Printed 

Circuit 

Board 

Component 

shown for

illustrative 

purpose

1. Determine the location of the Remote Temperature Probe.

The Remote Temperature Probe must be installed: 
a. On a vertical surface 
b. 1.2-1.5 meters above the floor
c. Away from the steam head
d. Not exposed to direct steam emission.

The probe has an integral 9 meter 
cable. Insure that the probe and/or 
steam generator are located accordingly.  
Contact a SAWO technical service 
representative if a longer cable is 
required.

2. Drill an 8mm hole in the wall as 

shown in Diagram 1. Do not 
oversize or undersize the hole. 
Clean area thoroughly.

3. Remove the knock-out from the 

steam generator jacket as shown in 
Diagram 2.

4. Insert the remote temperature 

probe cable through the 
knock-out and connect to the 
connector on the steam 
generator printed 
circuit board marked "TEMP 
PROBE" as shown 
in Diagram 2.

NOTE: 

For illustrative purposes only.
Consult. with qualified designer, 
architect or contractor for steam 
room construction details.

                          

Install the SAWO Control according to the installation and operation 

instructions supplied with the control. Failure to do so may result in an inoperative 
control and a hazardous condition.

!

CAUTION

                      The Remote Temperature Probe is for use with SAWO Control only. Do not use 
any other controls. Do not use any other temperature probe with the SAWO control. 
Noncompatible products may result in an inoperative control and a hazardous condition.

!

CAUTION

STS

230V 1N~
kW

KATSO OHJE

ISTA 

BEACHTEN SIE DIE 

ZUSÄTZLICHEN 

WICHTIGEN 

ANWEISUNGEN I

N DER 

BEDIENUNGSAN

LEITUNG

READ THE 

MANUAL

 FOR 

ADDITIONAL

 IMPOR

TANT 

INSTRUCTIONS

LÄGG  MÄRKE

 TILL DE 

VIKTIGA

 

15

Summary of Contents for STS120-3













Reviews: