background image

GA02041 

CR-158   COUPON PRINTER   OPERATIONS MANUAL 

COPYRIGHT 

This  manual  set  is  Copyright  © 

Innovative  Technology

  Limited.  No  part  of  this 

publication  may  be  reproduced  in  any  form  or  by  any  means  or  used  to  make  any 
derivative  such  as  translation,  transformation,  or  adaptation  without  permission 
from 

Innovative Technology

 Limited. The contents of this manual may be subject to 

change without prior notice. 

LIMITED

 

WARRANTY 

Innovative  Technology

  Limited  warrants  each  of  its  hardware  products  to  be  free 

from  defects  in  workmanship  and  materials  under  normal  use  and  service  for  a 
period commencing on  the  date  of  purchase  from 

Innovative Technology

 Limited 

or  its  Authorized  Reseller,  and  extending  for  the  length  of  time  stipulated  by 

Innovative Technology

 Limited. 

If  the  product  proves defective  within  the  applicable  warranty  period, 

Innovative 

Technology

  Limited  will  repair  or  replace  the  product. 

Innovative  Technology

 

Limited  shall  have  the  sole  discretion  whether  to  repair  or  replace,  and  any 
replacement product supplied may be new or reconditioned.  

The  foregoing  warranties  and  remedies  are  exclusive  and  are  in  lieu  of  all  other 
warranties,  expressed  or  implied,  either  in  fact  or  by  operation  of  law,  statutory  or 
otherwise,  including  warranties  of  merchantability  and  fitness  for  a  particular 
purpose. 

Innovative  Technology

  Limited  shall  not  be  liable  under  this  warranty  if  it’s  testing 

and examination disclose  that  the  alleged  defect  in  the  product  does  not  exist  or 
was  caused  by  the  customer's  or  any  third  person's  misuse,  neglect,  improper 
installation  or  testing, unauthorized attempts to repair, or any other cause beyond 
the  range  of  the  intended  use.  In  no  event  will 

Innovative Technology

  Limited  be 

liable  for  any  damages,  including  loss  of  profits,  cost  of  cover  or  other  incidental, 
consequential  or  indirect  damages  arising  out  the  installation,  maintenance,  use, 
performance,  failure  or  interruption  of  an 

Innovative  Technology

  Limited  product, 

however caused. 

Summary of Contents for CRU-158














Reviews: