background image

User Manual supplied on the CD-Rom included with the Quick start guide. 

“READ THE USERS MANUAL PRIOR TO OPERATION”

 

"Pay  special  attention to  the  SAFETY  Information  sections  of  the Quick  start 
guide and the user’s manual” 

   

Attention

 

Attention  mark  is  displayed  to  draw  ATTENTION  during  use.  Meter  could  be  damaged  or 

important Data may be lost if the unit is used improperly.   

   

Warning   

Warning  mark  is  displayed  to  indicate  improper  use.  Operating  outside  of  equipment  ratings 

could cause serious personal injury or fatal death. 

[Safety Symbol] 

    Table lists and describes the safety symbols shown on Meter or in User Manual. 

: DC (Direct Current or Voltage) 

: AC (Alternating Current or Voltage) 

: DC and AC 

: Earth Ground 

: Double Insulation 

: Power Supply OFF 

: Power Supply ON 

: Warning of Electric Shock 

: Warning of Danger 

:  Category

  1000V  Overload  Protection(Multi-meter  Function  :Model  SBS-600 

SBS-700 ) 

: Category

 600V Overload Protection(Multi-meter Function 

      Model SBS-600, SBS-700)   

:

 

Category

 300V Overload Protection(Scope Function, Model . SBS-700) 

[Notes for Safe Operation] 

WARNING: USE EXTREME CAUTION IN THE USE OF METER 

The improper use of meter may result in injury or death. 

Follow  all  safeguards  in  this  manual,  in  addition  to  the  normal  safety  precautions  used  in 
working with live electrical circuits. 

DO NOT ATTEMPT TO SERVICE the meter if you are not qualified to do so. 

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com 

Summary of Contents for SBS-600


















Reviews: