Scag Power Equipment SE-3.5BS Operator'S Manual Download

Page: 14 / 16

481886

Engine, 3.5 HP. Briggs & Stratton

04001-12

Bolt, Hex Head 5/16-18 x 1.75"

04030-03

Lockwasher, 5/16" Spring

04021-10

Locknut, 5/16-18 Hex Elastic Stop

04063-05

Key, 3/16 x 3/16 x 1.50"

48451

Pulley, 2.50 Dia. - .75 Bore Engine

45291

Engine Adapter Bracket

44048

Belt Guide, Engine

04041-07

Flatwasher, 3/8" (.391 x .938 x .105)

10 04001-16

Bolt, Hex Head 5/16-24 x 1.25"

11 04001-43

Bolt, Hex Head 5/16-24 x .75"

12 48114-04

Grease Fitting

13 46321

Idler Pulley Arm Assy.(Includes
Bushings & Grease Fittings)

14 04050-02

Retaining Ring, 3/4" External "E"

15 04001-21

Bolt, Hex Head 3/8-16 x 1.75"

16 48441

Pulley, Idler

17 04030-04

Lockwasher, 3/8" Spring

18 04021-09

Nut, 3/8-16 Hex Elastic Stop

19 48144

Grip, Height Adjustment Lever

20 45229

Height Adjustment Lever

21 43147

Index Pin

22 04041-10

Flatwasher, 3/8" (.375 x 2.0 x .060)

23 48050

Spring

24 45288

Control Rod, Wheel Height Adjustment

25 43138

Sleeve

26 42595

Plate, Height Adjustment Index

27 04020-04

Nut, Hex 3/8-16

28 04001-11

Bolt, 5/16-18 x 1-1/2" Hex Head

29 461178

Handle Assembly, (Includes Grips & Decal)

30 48448

Grip, Handle

31 04001-44

Bolt, Hex Head 1/4-20 x 1/2"

Ref. Part
No. No.

Description

LAWN EDGER SE-3.5BS

* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.

32 04012-04

Set Screw, 5/16-18 x 3/8"

33 04030-02

Lockwasher, 1/4" Spring

34 48454

Decal, SCAG

35 481043

Decal, Warning

36 04062-02

Hair Pin, .080 x 1.19

37 48100-05

Bearing, Oilite

38 44039

Control Rod, Upper

39 04001-09

Bolt, Hex Head 5/16-18 x 1"

40 45269

Control Rod, Lower

41 45226

Frame Weldment, Engine Deck

42 42591

Debris Guard

43 43141

Spacer, Rear Wheel

44 48446

Wheel, Rear

45 43211

Washer, Step 2.00" Dia.

46 04021-07

Nut, 1/2-13 Hex Elastic Stop

47 45228

Spindle Boom Weldment

48 48453

Rubber Deflector

49 04020-03

Nut, Hex 5/16-18

50 46359

Blade Guard, With Decal

51 04001-84

Bolt, 1/2-13 x 4-1/2" Hex Head

52 04004-11

Stud, 5/16-18 x 3" Grade 5

53 48452

Belt

54 04040-04

Flatwasher, 5/16" (.344 x .688 x .065)

55 48444

Blade

56 04020-07

Nut, Hex 1/2-13

57 48626

Pulley Spindle

58 43139

Shaft, Spindle

59 48442

Bearing, Spindle

60 42584

Belt Guide

61 48440

Wheel, Front

62 45231

Bracket, Front Wheel

63 04001-47

Bolt, Hex Head 3/8-16 x 5"

481043

48454

COMMERCIAL EDGER

481043

USE EYE PROTECTION. ROTATING BLADE MAY THROW OBJECTS.
KEEP AREA CLEAR OF BYSTANDERS TO REDUCE RISK OF INJURY.
DO NOT OPERATE WITHOUT GUARDS IN PLACE. DO NOT LEAVE
ENGINE RUNNING UNATTENDED. READ OPERATOR'S MANUAL
BEFORE USE.

WARNING

Summary of Contents for SE-3.5BS

















Search results

Summary of Contents for SE-3.5BS

Reviews:

Related manuals for SE-3.5BS

Brands by name

Popular brands

Scag Power Equipment SE-3.5BS, Operator'S Manual

Search results

Summary of Contents for SE-3.5BS

Reviews:

Related manuals for SE-3.5BS

Brands by name

Popular brands