background image

6

Section 2

R

 DANGER

DO NOT run the engine inside a building or 
a confined area without proper ventilation. 
Exhaust fumes are hazardous and contain 
carbon monoxide which can cause brain injury 
and death.

22.  Keep hands and feet away from all other moving 

parts. Contact can injure.

23.  Use care when approaching blind corners, shrubs, 

trees, or other objects that may obscure vision.

24.  NEVER leave the machine running unattended.

2.5 MAINTENANCE CONSIDERATIONS & 
STORAGE

1.  Check wear liners and impeller on a regular basis 

for bent, worn or cracked blades. Only replace 
impellers. Do not straighten or weld the impeller 
fan.

2.  Never make adjustments to the machine with the 

engine running unless specifically instructed to do 
so. If the engine is running, keep hands, feet, and 
clothing away from moving parts.

3.  Never operate the machine when uncoupled from 

the tow vehicle.

4.  Disconnect spark plug wire to prevent accidental 

starting of the engine when servicing or adjusting 
the machine. Wait for all movement to stop before 
adjusting, cleaning or repairing.

5.  Keep all nuts, bolts and screws tight, especially 

the impeller bolt, to ensure the machine is in safe 
working condition. 

6.  Do not change the engine governor settings or 

overspeed the engine. See the engine operator's 
manual for information on engine settings.

7.  To reduce fire hazard, keep the muffler and engine 

free of grass, leaves, excessive grease, oil and 
dirt.

8.  Park the machine on level ground.

9.  Block the wheels to prevent the machine from 

moving.

10.  Lower the Support Leg to the ground and secure 

with the spring latch when the machine is not 
attached to a tow vehicle. See Figure 2-1.

 

 

SPRING LATCH

REAR SUPPORT
LEG

Figure 2-1. Lowering the Rear Support Leg

11.  NEVER allow untrained personnel to service the 

machine.

12.  Keep all parts in good working condition. Replace all 

worn or damaged decals.

13.  Use jack stands to support components when 

required.

14.  Let the engine cool before storing.

15.  Keep the unit locked in a secure location and 

disconnect the battery to prevent unauthorized 
personnel, especially children, from playing and/or 
tampering with the unit.

16.  DO NOT store the machine near an open flame.

17.  Always follow the engine manufacturer's 

recommendation for storing and returning to service.

18.  Shut off fuel while storing or transporting.

2.6 USING A SPARK ARRESTOR

The engine on this machine may not be equipped with a 
spark arrestor muffler. It is in violation of California Public 
Resource Code Section 4442 to use or operate this 
engine on or near any forest covered, brush covered or 
grass covered land unless the exhaust system is equipped 
with a spark arrestor meeting any applicable local or state 
laws. Other states or federal areas may have similar laws. 
Check with your state or local authorities for regulations 
pertaining to these requirements.

2.7 SPARK IGNITION SYSTEM

This  spark  ignition  system  complies  with  Canadian       
ICES-002.

Summary of Contents for TLB25-35BV Series







































Reviews: