Scaime GM 80 PA Operating Instruction Download

Page: 16 / 16

Supplement

Device Disposal:

Please dispose the unserviceable device according to the legal rules.
By this you meet the legal obligations and contribute to the environmental protection!

Tendance:

The device may be cleaned with a slightly moistened cloth.

FAQ – Trouble Shooting

Device can not be turned on

Battery/accumulator inserted correctly?
Connect power supply at operation with accumulators.

The display begins to flash.

Charge the accumulators and/or exchange the batteries.

The calibrated adjustments do not match with the sensor anymore.

Was the sensor overloaded?
Is the correct sensor selected?

Possibly recalibrate the sensor.

Wrong values are indicated after the calibration

Was the sensor type selected correctly?

At calibration with calibration control check sensor for this option.

NU-GM80PA-TG-E-0115

Summary of Contents for GM 80 PA

















Search results

Summary of Contents for GM 80 PA

Reviews:

Related manuals for GM 80 PA

Brands by name

Popular brands

Scaime GM 80 PA, Operating Instruction

Search results

Summary of Contents for GM 80 PA

Reviews:

Related manuals for GM 80 PA

Brands by name

Popular brands