background image

4

A S S E M B LY

Distance to flammable walls

Positioning your wood-burning stove

The wood-burning stove must be set up so that the stove itself, the 
flue pipe, and the chimney can all be cleaned.

Position in relation to non-flammable walls

When positioning near a non-flammable wall, keep a minimum 
distance of 50mm between the rear of the product and the wall.

2

0

0

200

2

0

0

400

Distance to furniture:  800 mm

But please check to avoid furniture or other furnishings being dried 
out due to being too close to the stove.

45° Corner installation

Parallel rear wall installation

1

0

2

1

2

2

7

**

*

9

0

0

*

9

9

0

**

510

510

2

5

5

Scan 

50

1

1

4

1

510

2

2

7

**

*

9

0

0

*

2

5

5

1

1

1

0

**

510

Scan 

50

 Maxi

Note:

The Scan 

50-5

 Maxi is 5 mm taller than the Scan

 50

 Maxi.

Note:

The Scan

 50-5

 is 5 mm taller than the Scan

 50.

*  Centre rear outlet
**   Height to the beginning of 

the flue pipe at top outlet

*** Centre fresh air intake

*  Centre rear outlet
**   Height to the beginning of 

the flue pipe at top outlet

*** Centre fresh air intake

Summary of Contents for 50 Maxi













Reviews: