background image

M A I N T E N A N C E

10

Maintaining your wood-burning stove

Apart from regular chimney sweeping, your wood-burning stove 
does not require any regular maintenance.

Coated surfaces

Clean your wood-burning stove by dusting with a dry, lint-free cloth.

If the topcoat is damaged, you can purchase a repair spray from your 
authorised Scan dealer. As slight differences in colour are possible, 
spray a larger area to achieve a natural transition for best results. 
For best results, apply repair spray when the wood-burning stove is 
hand-hot.

Cleaning the glass

Our wood-burning stoves are designed to prevent serious soot build 
up on the glass. The best way to achieve this is to make sure you have 
a sufficient combustion air supply. It is also important to use dry 
wood, and have a correctly dimensioned chimney.

Even if you follow all of our instructions, a slight film of soot can 
build up on the glass. 

Before cleaning the glass, lock the door in the top position using the 
fastener.

Then open the door as follows: 

use the special tool included with your stove to release the screw 
on the door as shown below. Carefully lift and open the door. You 
can easily remove the sooty build up by cleaning with a dry cloth 
and glass cleaner. Your authorised Scan dealer stocks a special glass 
cleaner for this purpose.

Chimney sweeping and cleaning your 
wood-burning stove

Follow national and local chimney sweeping regulations. We 
recommend having the wood-burning stove cleaned regularly by 
the chimney sweep.
Before starting to clean your wood-burning stove, and sweep the 
flue pipe, we recommend first removing the smoke deflector plates.
Use only original replacement parts for maintenance and repairs of 
your stove.
Note! Make sure the stove is cold before starting maintenance or 
repair work. 

Removing the smoke deflector plates

Lift the lower smoke deflector plate, remove the pins at the sides, 
and then remove the plate. Remove the upper smoke deflector plate 
in the same way.

Combustion chamber lining

Slight cracks can appear in the combustion chamber lining due to 
moisture, or to the heating/cooling process. These cracks have no 
influence on the heating performance or lifetime of your stove. 
However, if the lining starts to crumble, you must replace it. The 
combustion chamber lining is not covered by the warranty.

Seals

All wood-burning stoves have seals made of ceramic material fitted to 
the stove, the doors, and/or the glass. These seals are subject to wear 
and tear, and must be replaced when necessary.

Summary of Contents for DSA 10

















Reviews: