background image

 

SHC 2000 

Warning label W09: 

Colours: yellow, black 

 

Danger area. 
Attention! Observe instructions.  
(operating manual, safety data sheet)

 

Mandatory label M018 

Colours: blue, white 

 

Carefully read the user information prior to 
beginning operation 

Scope: EU 

Semi S1-0701 
Table A1-2 #9 

 

Carefully read the user information prior to 
beginning operation 

Scope: NAFTA 

Particular care and attention is necessary because of the wide operating range.  
There are thermal dangers: Burn, scald, hot steam, hot parts and surfaces that can be 
touched. 

Warning label W26: 

Colours: yellow, black 

 

 

Hot surface warning. 
(The label is put on by  ScanCool  ) 

Observe the instructions in the manuals for instruments of a different make that you 
connect to the circulator, particularly the respective safety recommendations. Also 
observe the pin assignment of plugs and technical specifications of the products. 

 

Disposal: 

The product may be used with oil as bath fluid. These oils fully or partially consist of 
mineral oil or synthetic oil. For disposal, observe the instructions in the safety data 
sheets.  
Please observe the regulations for disposal which are effective in the country of 
operation. 

 
 

 

Valid in EU countries 
Directive 2002/96/EC of the European Parliament and of the Council 
of 27 January 2003 on waste electrical and electronic equipment 
(WEEE). 
This directive requires electrical and electronic equipment marked 
with a crossed-out trash can to be disposed of separately in an 
environmentally friendly manner. 
Contact an authorized waste management company in your country. 
Disposal with household waste (unsorted waste) or similar collections 
of municipal waste is not permitted! 

 

Summary of Contents for SHC 2000
























Reviews: