12 english
Manufacturer
Scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We wish you much pleasure and success with your
new scheppach machine.
Note
In accordance with valid product liability laws, the
manufacturer of this device shall not be responsible
for damage to and from this device which results from:
• Improper care.
• Noncompliance with the Operating Instructions.
• Repairs made by unauthorized persons.
• The installation and use of any parts which are not
original scheppach replacement parts.
• Improper use and application.
• Failure the electrical system as a result of noncom-
pliance with the legal and applicable electrical direc-
tives and VDE regulations 0100, DIN 57113 / VDE
0113.
We recommend
that you read through the entire operating instructions
before putting into operation.
These operating instructions are to assist you in get-
ting to know your machine and utilize its proper ap-
plications.
The operating instructions contain important notes on
how you work with the machine safely, expertly, and
economically, and how you can avoid hazards, save
repair costs, reduce downtime and increase the reli-
ability and service life of the machine.
In addition to the safety requirements contained in
these operating instructions, you must be careful to
observe your country’s applicable regulations.
The operating instructions must always be near the
machine. Put them in a plastic folder to protect them
from dirt and humidity. They must be read by every
operator before beginning work and observed consci-
entiously. Only persons who have been trained in the
use of the machine and have been informed of the
various dangers may work with the machine. The re-
quired minimum age must be observed.
In addition to the safety requirements contained in
these operating instructions and your country’s appli-
cable regulations, you should observe the generally
recognized technical rules concerning the operation
of woodworking machines.
General notes
• After unpacking, check all parts for any transport
damage. Inform the supplier immediately of any
faults.
• Later complaints cannot be considered.
• Make sure the delivery is complete.
• Before putting into operation, familiarize yourself
with the machine by carefully reading these instruc-
tions.
• Use only original scheppach accessories, wearing
or replacement parts. You can find replacement
parts at your scheppach dealer.
• When ordering, include our item number and the
type and year of construction of the machine.
Lata 5.0
Included with delivery
Wood turner lathe
Tool holder
Driver (Fig. 1.2, A)
Live tailstock center
Tensioning spindle (Fig. 1.2, C)
Face plate
Openend wrench SW 32 (figure 1.2, D)
Operating instructions
Technical data
Dimensions
L x B x H mm
1610 x 490 x 1175
Bed height mm
910
Headstock thread
Art. Nr. 8800 1925 (1" x 8 TPI)
Art. Nr. 8800 1926 (M 33)
Spindle cone
MK 2
Height of centers
above bed mm
175
Width between
centers mm
1050
Diameter above
bed mm
355
Diameter
between centers
mm
282
Length of tool
holder mm
300
Face plate ø mm
150
Weight kg
85
Wood turning spindle with dust-proof precision grooved ball
bearing
Revolutions 1/min
500/600/750/900/1100/
1200/1400/1600/1800/2100
Tailstock
Tailstock cone
MK 2
Tailstock drill hole
(hollow spindle)
ø mm
9
Tailstock sleeve
adjustment mm
55
Drive
Electric Motor
230–240V/50 Hz
Input P1 kW
0,75
Output P2 kW
0,50
Revolutions 1/min
1400
Motor protection
yes
Undervoltage
release
yes
Switch - plug
combination
Netzstecker
Operating mode
S6 40%
Noise parameters
The noise emission values at the work place, deter-
mined according to EN 23746 (acoustic power levels)
and EN 31202 (acoustic pressure levels) with a cor-
rection factor k3 calculated according to appendix A.2
of EN 31204, based on operating conditions listed in
ISO 7904, appendix A, are:
Summary of Contents for 1902301901
