Scheppach 4903302901 Instruction Manual Download

Page: 24 / 88

www.scheppach.com

24 | GB

• Remove the grinding/sanding belt (6) to the rear.
• Mount and the new grinding/sanding belt in reverse

order. Important. Note the running direction: On the
housing and on the inside of the grinding/ sand-
ing belt!

8.3 Adjusting the grinding/sanding belt (6)

• Pull out the power plug
• Push the grinding/sanding belt (6) by hand slowly in

the running direction.

• The grinding/sanding belt (6) must run centrally on

the grinding/sanding surface. If not, you can use the
knurled screw (8) to make adjustments.

8.4 Moving the grinding/sanding position of the

grinding/sanding belt (6) (fig. 10-12)

• Loosen the Allen screw (5)
• Move the grinding/sanding belt (6) upwards into the

desired position.

•

Tighten the Allen screw (5) again to fix this position.

• In this position you can use the grinding/ sanding

table to support the workpiece. To do this, first loos

en the two Allen screws (17) and then remove the
stop rail (7). The grinding table can now be pushed

into the hole in the holder tube (20) and fixed with

the screw (1)

8.5 Replacing the abrasive paper on the grinding/

sanding disk (11)

Dismantle the bottom wheel guard (15) by removing
the 2 screws (16). Pull the sanding/ grinding paper

off the sanding/grinding disk (11) and attach the new
sanding/grinding paper (quick-fit fastening system).

Mounting belt/disc sander to work bench

If your belt/disc sander is to be used in a permanent
location, it is recommended you secure it to a work-
bench or other stable surface.
• Mark holes on workbench where belt/disc sander is

to be mounted using holes in the base as a template
for hole pattern.

• Drill holes through workbench.
• Place belt/disc sander on workbench aligning holes

in the base with holes drilled in the workbench.

• Insert bolts (not included) and tighten securely with

lock washers and hex nuts (not included). Note: All
bolts should be inserted from the top. Install the
lock washers and hex nuts from the underside of
the workbench.

Wear hearing protection.

The effects of noise can cause a loss of hearing. Total

vibration values (vector sum - three directions) deter-
mined in accordance with EN 62841-1.

8. Attachment and operation

Before starting the equipment

Before you connect the equipment to the mains supply
make sure that the data on the rating plate are identi-
cal to the mains data.

Warning!

Always pull the power plug before making adjustments
to the equipment.
• All covers and safety devices have to be properly

fitted before the equipment is switched on.

• It must be possible for the grinding/sanding belt

and disk to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails
or screws, etc.

•

Before you actuate the On/Off switch, make sure
that the abrasive paper is correctly fitted and that

the equipment‘s moving parts run smoothly.

8.1 Assembling the machine (fig. 1 - 5)

• Mount the lower wheel guard (15) with the screws

(16). (fig. 2)

• Mount the grinding/sanding table (14) and secure

with the screw (1). (fig. 3+4) The grinding/ sanding
table (14) can be infinitely adjusted from 0° to 45°

with the miter scale (2) and the thumb screw (1).

• The adjustable cross stop (13) ensures safe guid-

ance of the workpiece. Important. The grinding/
sanding disk (11) must be able to run freely, but the
distance between the grinding/sanding table (14)
and the grinding/sanding disk (11) is not allowed to
exceed 1.6 mm.

• Put on the stop rail (7) and secure with the screw

(17). (fig. 5) Important. The grinding/sanding belt (6)

must be able to run freely.

8.2 Changing the grinding/sanding belt (6)

(fig. 6 - 9)

•  Pull out the power plug
•  Remove the screws (18).
•  Remove the grinding/sanding belt guard (19).
•  Turn the grinding/sanding tensioner (10) to the right

in order to reduce the tension on the grinding/sand-
ing belt (6).